Ford Bronco Sport, Dual S1/S2 Reverse kit instructions

Ford Bronco Sport, Dual S1/S2 Reverse kit

instructions

185 Bosstick Boulevard • San Marcos • CA • 92069

Phone 760-560-2252 X3 • Fax 760-560-0383

info@bajadesigns.com • www.bajadesigns.com

LIMITED LIFETIME WARRANTY

Baja Designs proudly offers a LIFETIME WARRANTY against manufacturer’s defect on all the products

that we manufacture.

These are comprehensive warranties; other than the exclusions below – you’re covered. If your LED

or HID bulb burns out, you’re covered. Additionally, cutting off our connector or changing your lenses

does not automatically void your warranty.

Exclusions:

Installation errors, abuse, misuse or crash damage. You must be the original owner of the product and

can supply proof of purchase.

Baja Designs manufactures its own products as well as resells products manufactured by others. Baja

Designs makes no express or implied warranties on products not manufactured by Baja Designs

including without limitation any warranties or merchantability and fitness for a purpose. We will,

however, pass on all warranties made by the manufacturer, who has sole responsibility for performing

such warranties.

Baja Designs will pay the freight if your product is less than 90 days old, otherwise defective products

must be returned to Baja Designs, Inc., freight prepaid. At our option, we will repair or replace items in

question and return them at no charge. If the identical product is no longer available, we will replace

with a similar product of equal value. Baja Designs Inc. will not be responsible for any indirect or

consequential damages in connection with defective merchandise.

Items purchased through a Baja Designs authorized dealer must be returned through the dealer. Only

available on LED auxiliary lights and product must be in sellable condition at MSRP. Product that has

been damaged in any way after the original purchase date will be excluded from this guarantee.

Indemnification:

Buyer hereby acknowledges off-roading, racing and driving at night are dangerous activities

and that the products and/or supplies purchased from Baja Designs are used in an inherently

dangerous activity that may endanger life and limb; and in no event shall the seller, or seller's

heirs and assigns, be held liable for consequential damages, nor shall seller's liability on any

claim for damages arising out of or connected with the sale, delivery, or use of purchased

products and/or supplies exceed the purchase price of the products and/or supplies

Ford Bronco Sport S2/S1 Reverse Light Kit Instructions

Tools Required:

- 10mm Socket and extension

- Flat head and Trim tool

- ¾” Step drill (Required)

S2:

- 9/16” Wrench and Socket

- 4mm Allen Wrench

S1:

- 7/16” Wrench and Socket

- 3mm Allen Wrench

1. Locate the hole through the receiver hitch.

(above the receiver pin holes and closer to the

bumper)

2. Assemble the two L-brackets onto either side of

the receiver hitch using the provided hardware.

3. Place the mounting hardware into the standard

light brackets before mounting to the lights.

Assemble each Squadron (or S1) to their

standard bracket using the 4mm Allen wrench (or

3mm Allen wrench). Mount the assemblies to the

L-brackets with the 9/16” (or 7/16”) wrench and

socket.

4. Attach the small splitter harness to the power

cords and route the wires behind the plastic

bumper on the driver side. (Make sure to tie the

harness away from the muffler near the towing

electrical connector). Attach the extension

harness and route it over the lower driver side

control arm. Take the main harness light lead

and route it from the inside the engine

compartment, down the driver side firewall, and

connect it to the extension harness.

Driver

Side

Passenger

Side

(-)

Grommet

(+)

Firewall Grommet location

Battery

Harness Route

5. Attach harness leads to each power cords and

route along the upper firewall. Use the

provided wire ties to fasten the harness to the

plastic inner wiper cowling.

6. To route the switch through the firewall, the

battery will need to be removed. First, remove

the intake ducting from above the radiator by

prying the two arrowed plastic fasteners with

the trim tool.

7. Remove the circled connector on the air

cleaner cover and the two arrowed clips

attaching the harness. Using a flathead

screwdriver, remove the intake air boot clamp.

Pull up on the air cleaner box to remove and

set aside.

8. Loosen the circled battery clamp fasteners with

the 10mm socket with the extension. Remove

the battery terminals (+/-) with the 10mm

socket and place them aside; black lead first.

Now the battery can be slid forward and

removed for the moment. Remove the arrowed

firewall grommet and route the harness switch

lead through. Pull enough slack in from inside

the cab to reach the headlight controls.

Air

cleaner

9. Carefully use the trim tool inside the cab to

remove the panel to the left of the headlight

controls.

10. Carefully pull the edges of the headlight

control dash panel until the clips release.

Remove the arrowed headlight control unit

connector.

11. With the ¾” step drill bit, drill a hole in the

circled area shown. Take a quick photo of the

switch wire orientation, remove the switch

wires from the switch, route through the hole,

reconnect, and mount the switch. Plug the

headlight module back in and replace the dash

panels.

12. Install the battery and repeat steps 6-8 in

reverse order, this time attaching the positive

battery terminal first and then the ground

terminal. Mount the relay to the bolt on the strut

tower as shown in the image.

Re-torque all the fasteners after 100 miles.

Tie wires away from all hot, sharp, and/or rotating

components.

Your install is now complete! Thank you for

choosing Baja Designs.

Relay