Jeppesen FliteDeck Pro User Guide

Version 3.1.6 for iOS

User Guide

FliteDeck Pro

FliteDeck Pro User Guide

Jeppesen

55 Inverness Drive East

Englewood, Colorado 80112-5498

This document supports version 3.1.6 of Jeppesen FliteDeck Pro for iOS.

The minimum operating system requirement for this release is iOS 11.3.

At the time of this release, FliteDeck Pro 3.1.6 has been tested, and is compatible with, iOS 11.4.

For the most recent FliteDeck Pro 3.1.6 hardware and software requirement updates,

see the FliteDeck Pro iOS page on the Jeppesen Customer Support Portal.

June 2018

Document ID: DATD_Jepp_FDPro_iOS_3.1.6_UserGuide

Revision: 1.0

Table of Contents

Introduction

Additional References ............................................................................................................ 1

Technical Support .................................................................................................................. 1

Compatibility Statement ......................................................................................................... 1

Devices Supported .......................................................................................................... 2

Deployment Considerations ................................................................................................... 2

About the Initial App Download ....................................................................................... 2

App Update Considerations ............................................................................................ 2

Connectivity Considerations ............................................................................................ 3

Getting Started

Adjusting FliteDeck Pro Global Settings ................................................................................ 6

About Basic Touchscreen Gestures ................................................................................... 10

Overview .............................................................................................................................. 11

Using the Toolbar ................................................................................................................ 13

Adjusting Display Brightness ......................................................................................... 13

Viewing GPS Status ...................................................................................................... 13

Performing a Search ..................................................................................................... 14

Accessing Settings ........................................................................................................ 15

Locking the Display ....................................................................................................... 16

Setting Up Your Flight

Creating a Route Manually .................................................................................................. 18

Viewing SIDs and STARs Transition Points .................................................................. 19

About Route Points ....................................................................................................... 19

Editing Your Route in the Flight Info Drawer ................................................................. 19

Editing Your Route by Interacting with the Map ............................................................ 20

Working with User Waypoints ....................................................................................... 21

Direct To Routing .......................................................................................................... 24

Working with Saved Flights ................................................................................................. 27

Loading a Saved Flight ................................................................................................. 27

Saving the Active Flight ................................................................................................. 27

Duplicating a Saved Flight ............................................................................................ 28

Sorting Saved Flights .................................................................................................... 28

Deleting Saved Flights .................................................................................................. 28

Working with Shared Flights ................................................................................................ 29

Loading a Shared Flight ................................................................................................ 29

Table of Contents

Sharing an Active Flight ................................................................................................ 29

Sharing a Saved Flight without Loading It ..................................................................... 30

Working with Flight Plan Routes .......................................................................................... 30

Viewing Flight Plan Routes ........................................................................................... 31

Loading a Flight Plan Route .......................................................................................... 31

Saving a Flight Plan Route Without Loading It .............................................................. 32

Working with ATC-Cleared Routes ...................................................................................... 32

Viewing ATC-Cleared Routes ....................................................................................... 33

Loading an ATC-Cleared Route .................................................................................... 33

Saving an ATC-Cleared Route Without Loading It ........................................................ 33

Selecting Terminal Charts for Your Flight ............................................................................ 34

Selecting Terminal Charts for the Active Flight ............................................................. 34

About Chart Types ........................................................................................................ 35

Switching Between Route Airports ................................................................................ 35

Navigating Between Selected Charts ............................................................................ 36

Associating an Engine-Out Chart with a SID ................................................................ 36

Viewing Manuals and Change Notices ................................................................................ 37

Pubs Tab from the Enroute Map ................................................................................... 37

Pubs Tab from Terminal Charts View ........................................................................... 38

Accessing Enroute Information

Adjusting the Enroute Map View .......................................................................................... 40

About Enroute Map Themes ......................................................................................... 40

Switching Enroute Map Themes ................................................................................... 40

Displaying Ownship on the Enroute Map ...................................................................... 41

Moving Map ................................................................................................................... 41

Switching Map Orientation ........................................................................................... 41

Viewing Distance ........................................................................................................... 42

Working with the Route List ................................................................................................. 43

About the Route List ...................................................................................................... 43

Showing and Hiding the Route List ............................................................................... 44

Viewing the Route List with Moving Map ...................................................................... 44

Adjusting the Route Corridor ......................................................................................... 44

Viewing Object Details from the Route List ................................................................... 46

Changing the Display of Communication Frequencies ................................................. 46

Searching the Route List ............................................................................................... 47

Working with Publications .................................................................................................... 49

Viewing Jeppesen Airway Manuals ............................................................................... 49

Viewing Enroute Change Notices ................................................................................. 50

Viewing Company Manuals ........................................................................................... 51

Table of Contents

Viewing Route Notes ..................................................................................................... 52

Searching Publications .................................................................................................. 53

Viewing Enroute Map Object Details ................................................................................... 55

Viewing Airport Details .................................................................................................. 55

Viewing Airway Details .................................................................................................. 55

Viewing Fix and Waypoint Details ................................................................................. 56

Viewing Navaid Details ................................................................................................. 56

Viewing Airspace Details ............................................................................................... 56

Viewing Terrain Details ................................................................................................. 57

Viewing Cultural Details ................................................................................................ 57

Viewing Operational Notes ............................................................................................ 57

Viewing Tailored Enroute Data ..................................................................................... 57

Filtering Enroute Map Objects ............................................................................................. 59

Show and Hide Enroute Map Objects ........................................................................... 59

Searching for Enroute Map Objects from the Map ........................................................ 66

Displaying Enroute Weather ................................................................................................ 68

Accessing Terminal Information

Working with Terminal Chart Information ............................................................................ 70

Viewing Chart Change Notices ..................................................................................... 70

Highlighting a Chart ....................................................................................................... 70

Rotating a Chart ............................................................................................................ 71

Printing a Terminal Chart .............................................................................................. 71

Displaying Ownship Position on Terminal Charts ................................................................ 71

Displaying Ownship on Approach Charts ...................................................................... 71

Temporarily Disable Display of Ownship Position Approach Charts ............................. 72

Viewing the Off-Map Indicator on Approach Charts ...................................................... 72

Displaying Ownship on SID and STAR Charts ............................................................. 72

Displaying Ownship on Taxi Charts .............................................................................. 72

Automatically Displaying the Taxi Chart Upon Landing ................................................ 73

Displaying Terminal Weather ............................................................................................... 73

Displaying METAR/TAF ................................................................................................ 73

Working with Mid-Cycle Chart Updates ............................................................................... 74

Switching Between Two Available Charts While Viewing the Chart ............................. 74

Working with the Airport Moving Map (AMM) ...................................................................... 75

Managing Data Updates

Performing Data Updates .................................................................................................... 78

Performing Data Updates .............................................................................................. 78

Table of Contents

Switching Between Two Available Enroute Databases ................................................. 79

About Unscheduled Updates ............................................................................................... 80

Performing an Unscheduled Update ............................................................................. 80

Understanding Messages and Error Codes ......................................................................... 81

Introduction

Additional References

Introduction

FliteDeck Pro is a mobile electronic flight bag (EFB) solution designed for commercial and business aviation

flight crews. This guide provides a basic description of how to use FliteDeck Pro.

Additional References

Jeppesen provides detailed, task-oriented training and documentation on the

Jeppesen Customer Support Portal page.

Help is also available from within the app by tapping Settings > Help from the

FliteDeck Pro toolbar.

Technical Support

Many operators provide their own technical support for FliteDeck Pro. That

technical support contact information may be available to you from within the app

by tapping Settings > Help from the FliteDeck Pro toolbar.

In addition, Jeppesen provides technical support 24 hours a day, 7 days a week

at:

• North America Toll Free: 800-537-7225

• United States Direct: 303-328-6175

• International: 49-6102-507004

• Email: [email protected]

• Online Support: https://support.jeppesen.com

Compatibility Statement

The minimum operating system for FliteDeck Pro 3.1.6 is iOS 11.3. At the time of

this release, FliteDeck Pro 3.1.6 has been tested, and is compatible with iOS

11.4. FliteDeck Pro tests against, and supports, iOS English (U.S.) language.

Jeppesen iOS applications are continually modified to improve performance and

to be fully compatible with the most recent Apple iOS and iOS devices.

Check the Jeppesen Customer Support Portal page for any updates to this

compatibility statement.

Introduction

Deployment Considerations

Devices Supported

FliteDeck Pro 3.1.6 is supported on the following devices:

• iPad Pro, 10.5-inch

• iPad, 5th generation

• iPad Pro, 9.7-inch

• iPad Mini 4

• iPad Air 2

• iPad Mini 3

• iPad Air

• iPad Mini 2

NOTE: The iPad Air 2, and later, are recommended devices.

Deployment Considerations

FliteDeck Pro is released through available Apple distribution models. Only one

version of the app can be downloaded to the iPad at a time. It is a best practice to

force-close the app before updating to a new version.

The FliteDeck Pro app and data, including subsequent data updates, requires 2 to

6 GB of available storage capacity on the iPad. The variability in the storage

capacity requirement is related to the size of your coverage area.

Any additional data, such as Airport Moving Map (AMM) or supplemental enroute

data, will affect storage requirements.

About the Initial App Download

FliteDeck Pro requires an initial data download to use the app outside of Demo

mode. One way to activate and complete the initial download of data, involves

receiving a JDMNotification email on your device from your company EFB admin-

istrator with instructions on how to proceed.

App Update Considerations

When updating to FliteDeck Pro 3.1, note the following:

• There is a new cultural data set (500mb) that is downloaded with the app

update.

• The time necessary to download and perform data updates depends on the

speed of your Internet connection and size of your coverage area.

• Ensure that you allow for the necessary time to complete the update before

beginning the update.

Introduction

Deployment Considerations

What is Preserved When Updating the App

When FliteDeck Pro is updated from one version to another, the app preserves

the following information:

• Customized FliteDeck Pro global settings under user control, including

registration and account information

• Saved Flights

Disabling Automatic App Updates

Apple iOS offers automatic background app updates. When a device is fully

charged and connected to the Internet, any free apps installed on the device will

be updated without requiring any interaction from you. This feature might not

always be desirable. To prevent automatic FliteDeck Pro updates and to avoid

downloading at an inopportune time, you can:

1. Tap Settings from the iPad Home screen.

2. Tap iTunes & App Store.

3. Under Automatic Downloads, switch Apps to OFF.

NOTE: Preventing the automatic update of the app does not impact the

availability of reoccurring data updates to FliteDeck Pro.

Connectivity Considerations

FliteDeck Pro requires a reliable Wi-Fi or cellular Internet connection to perform

many of its capabilities. In addition to downloading data updates, for example, an

Internet connection is required to download Organized Track System data, load

new routes sent from a flight-planning system, download weather, and refresh the

list of ATC-cleared routes.

NOTE: Sharing flight information between iPads requires a Wi-Fi and Bluetooth

connection.

FliteDeck Pro displays ownship position based on the built-in iPad GPS, or any

external GPS device that may be used. The minimum required GPS accuracy to

display ownship is:

• Enroute map = 600 meters

• Approach charts = 200 meters

• SID and STAR charts = 200 meters

• Taxi (10-9) charts = 25 meters

• Airport Moving Map = 45 meters

FliteDeck Pro alerts you when minimum GPS accuracy requirements have not

been met by:

• Displaying an amber badge on the GPS Status button;

• Removing the ownship symbol from the map or chart, if set to display; and

• Removing the Present Position button from the map.

Introduction

Deployment Considerations

About Connecting to an Aircraft Interface Device

A new setting under Services in FliteDeck Pro global settings is introduced with

FliteDeck Pro 3.1. This setting is the Datasource Selector.

FliteDeck Pro added support for the Teledyne GroundLink® AID+. When

Teledyne is selected, FliteDeck Pro searches for a Teledyne AID connection in

your aircraft.

Aircraft Interface Devices, or AIDs, enable FliteDeck Pro to more quickly and

consistently transfer flight critical data between an aircraft's existing onboard data

system and your iPad.

There is currently only one option available and that is Teledyne. The default

setting is set to None.

NOTE: Operators may be required to obtain additional authorization to use this

functionality. Any offset to the GPS antenna will need to be accounted for

in determining the total accuracy of the system.

FIGURE 1: FliteDeck Pro Global Settings - Services > Data Source

NOTE:

If your operation obtains GPS source for the FliteDeck Pro application

from an Aircraft Interface Device, please note that the GPS antennae may

be offset from the cockpit and correspondingly shift the display of the

ownship position on the map. The offset to the GPS antenna will need to

be accounted for in determining the total accuracy of the system.

FliteDeck Pro displays the GPS source used by your iPad from the GPS Status

button on the FliteDeck Pro toolbar.

Getting Started

djusting FliteDeck Pro Global Settings

Getting Started

Getting started with FliteDeck Pro is easy. You set up global settings to fit your and your company’s needs and

then use basic touchscreen gestures to interact with the app.

Adjusting FliteDeck Pro Global Settings

Your company EFB administrator may preconfigure certain FliteDeck Pro global

settings. Any changes that you make to those preconfigured settings will not take

effect when you launch FliteDeck Pro. Any settings that are not preconfigured

remain under your control.

All settings are preserved and do not change between subsequent launches, or

when you upgrade from one version of FliteDeck Pro to another.

 To access FliteDeck Pro global settings:

1. Tap Settings from your iPad Home screen.

2. From the list of apps, tap JeppFD-Pro.

Allowing Location Services

Switch Location Services to ON to allow FliteDeck Pro to use information

based on the current location of your iPad to provide location-based

services.

Allowing Notifications

For those authorized to display ownship or moving map in flight, you can switch

Notifications to ON to direct FliteDeck Pro to use the Notifications Center on your

iPad to deliver Lock Screen notifications to your iPad alerting you that you are

reaching a reporting time along your route.

Adjusting Sleep Mode

Switch Sleep Mode OFF to prevent your iPad from going into sleep mode during

periods of inactivity. This setting is ON by default.

NOTE: Switching Sleep Mode OFF reduces the iPad battery life.

Getting Started

Adjusting FliteDeck Pro Global Settings

Sending and Receiving Flight Info

 Adjust these settings to send and receive routes:

• Switch Allow Flight Sharing to ON to allow FliteDeck Pro to share flight

information between iPads.

NOTE: Starting with iOS 11, both Wi-Fi and Bluetooth settings need to be set to

ON in device settings for successful FliteDeck Pro route sharing.

• Switch Display ATC Clearances to ON to enable FliteDeck Pro to retrieve and

display ATC-cleared routes.

Adjusting the Enroute View

NOTE: Displaying ownship position on the enroute map is designed to improve

flight crew situational awareness during enroute flight. Do not use this

functionality as the basis for navigation. Operators may be required to

obtain additional authorization to use this function.

 Adjust these settings to customize your view of the enroute map:

• Switch Moving Map to ON to track ownship position on the map and in the

route list, recenter the enroute map over aircraft location after panning away,

and view the enroute map in a track-up orientation.

• Switch Display Ownship to ON to display your aircraft position on the enroute

map and indicate the next point along your route in the Route list (with a

vertical magenta line).

• Switch Display VFR Theme to ON to display the VFR enroute theme.

• Switch Display Organized Track Systems to ON to direct FliteDeck Pro to

retrieve and display organized track systems on the enroute map.

NOTE: Jeppesen recommends that you have an established Internet connection

the first time you switch Display Organized Track Systems to ON.

Adjusting the Terminal Charts & AMM View

NOTE: Displaying ownship position in the terminal area is designed to assist flight

crews in orienting themselves on the airport surface and to improve pilot

positional awareness during taxi operations. This functionality is not to be

used as the basis for ground maneuvering and is limited to ground

operations.

 Adjust these settings to customize the view of your terminal charts and

Airport Moving Map:

• Switch Display Ownship on Approach Charts to ON to display aircraft

position on approach charts. This setting also enables the display the off-

screen indicator on approach charts.

• Switch Display Ownship on Taxi Charts to ON to display your aircraft

position on taxi charts.

Getting Started

djusting FliteDeck Pro Global Settings

• Tap the Default Chart Zoom Level to choose your preference for viewing

terminal charts. Fit Full Chart is the default value.

• Tap the Taxi on Speed Threshold to set the speed at which, if enabled, the

automatic switch to a taxi chart (or Airport Moving Map) occurs.

It is also the speed threshold at which the ownship, if enabled, displays on the

taxi chart. Values range from 30 to 80 knots. 40 knots is the default setting.

• The Airport Moving Map (AMM) flyout is available if your company subscribes

to AMM. Tap the Airport Moving Map (AMM) flyout to:

- Switch Display Ownship to ON to display ownship position on the

Airport Moving Map.

- Switch Moving Map to ON to track ownship position on the airport

moving map, recenter the map over aircraft position, and view the

Airport Moving Map in a track up orientation.

- Switch Set as Default on Landing to ON to direct FliteDeck Pro to

switch to the airport moving map (if the airport has one) upon landing.

AMM settings are available only if your company subscribes to Airport Moving

Map. AMM is not available for all airports. For more information on AMM, see

Working with the Airport Moving Map (AMM) on page 75.

Displaying Weather

 Adjust these settings to customize the display of weather

information:

• Switch Display Enroute Wx to ON to view weather data overlaid on the

enroute map.

• Switch Display METAR/TAF to ON to view METAR/TAF information.

• Tap the Temperature Unit flyout to select your preference for viewing

temperature units, Fahrenheit (default) or Celsius.

• Tap the Default METAR/TAF Format flyout to select your preference for

viewing METAR/TAF information, Raw (default) and Decoded.

Accessing Account Info

These settings provides FliteDeck Pro info and enables you to connect with other

services.

• Version displays the FliteDeck Pro version and build number.

• Tailored Enroute Data displays the company name if your company has

chosen to subscribe to and deliver supplemental enroute data. The setting

displays N/A when supplemental enroute data is not being received.

NOTE: When you launch FliteDeck Pro for the first time after downloading tailored

enroute data, you might be prompted to select the fleet to which the

enroute data will apply.

• Tap the Terminal Charts Coverage Codes flyout to display the terminal chart

coverage codes that are on your iPad. This information may be used as a

reference for technical support.

Getting Started

Adjusting FliteDeck Pro Global Settings

 Adjust these settings to connect with other services:

• Tap the Services flyout to enter credentials for importing flight plan routes

from flight planning systems and to receive company-uploaded documents.

NOTE: For more information about credentials, contact your EFB administrator

or Jeppesen account manager.

• Tap the Datasource Selector flyout and tap Teledyne if you ant to

FliteDeck Pro to search for the Aircraft Interface Device on your aircraft. If

FliteDeck Pro finds the Teledyne AID, it negotiates certificates and, if

authorized, will connect to it.

• Registration Info displays the recipient name for the delivery of data to your

iPad.

• You can switch Share Registration Info to ON so that you can share

FliteDeck Pro registration information to register other apps on your iPad.

 To share FliteDeck Pro registration information with another app:

1. Switch Share Registration Info to ON.

2. Launch FliteDeck Pro and confirm that you want to share registration.

3. Launch the app with which you want to share registration information.

Accessing Support Information

These settings provide access to technical support, application information, and

other setting controls.

• Tap the Support flyout to display contact information for FliteDeck Pro

technical support.

In addition, there are Send log files via Email and Allow Simulated

Location options. Both of these options are used by technical support for

testing purposes. Both options are set to OFF by default.

• Tap the Terms & Conditions flyout to display links to both the current

Application and Data Terms and Conditions.

• You can switch Reset User Settings to ON to restore FliteDeck Pro settings

to the default values. To complete the action – after you switch to ON, you

must launch FliteDeck Pro and confirm that you want to reset user settings.

• You can switch Deactivate the App to ON to remove all Jeppesen data and

clear the activation information from the iPad.

NOTE: Deactivation removes all Jeppesen data and clears the registration and

coverage code information from the iPad.

 To deactivate FliteDeck Pro:

1. Switch Deactivate to ON.

2. Launch FliteDeck Pro and confirm that you want to deactivate the app.

3. Tap Proceed

Getting Started

bout Basic Touchscreen Gestures

About Basic Touchscreen Gestures

Use basic touchscreen gestures to interact with FliteDeck Pro.

Zoom In or Out

Zoom in and out of the display by moving your thumb and finger in a pinching

gesture.

Touch, Hold, Release

You can touch, hold, and release any object on the enroute map to view more

information about it. Depending on the type of object, you may also be able to add

it to, or remove it from your route.

Double-Tap to Zoom Out

When you have zoomed in on a terminal chart or AMM depiction, you can double-

tap to zoom back out to the full extent of the chart or map depiction. When you

have zoomed in the enroute map, you can double-tap to view the full extent of

your route.

Two-finger Swipe to Navigate

Swipe left or right with two fingers to flip through selected terminal charts.

Four-Finger Swipe Between Open Apps

Swipe left or right with four fingers to move back and forth between one open app

and another. For example, you can do this gesture to navigate back and forth

between an open PDF reader and FliteDeck Pro.

Getting Started

Overview

FliteDeck Pro makes it easy to access the information you use most.

About the Control Bar

Whether you are viewing terminal charts or the enroute map, FliteDeck Pro

displays the same buttons from the control bar along the left-side of the display.

• Tap the Route list button from the enroute map to show and hide the Route

and Pubs tabs. Tapping the Route list button from terminal chart view displays

Chart Change Notices for the selected airport.

• Tap the Airports button, which is labeled with the name of the selected airport,

to change the airport for which you are viewing terminal charts.

• Terminal charts for the selected airport are organized by chart type and display

along the control bar (REF, CO, STAR, APP, TAXI, and SID) and are available

by tapping a chart type category.

• Tap the Enroute Theme button, which is labeled with the selected enroute

theme, to switch enroute themes from the enroute map. Tapping the Enroute

Theme button while viewing terminal charts, switches your view from terminal

charts to the enroute map.

• Tap the weather (Wx) button to display terminal or enroute weather depending

on your view.

About the Flight Info Drawer

 To open and close the Flight Info drawer:

• Tap the Flight Info drawer tab.

The Flight Info drawer is where you create and load new flights. It is also where

you can edit, save, and share flights; import flight plan routes, and access ATC-

cleared routes.

The selected enroute map theme displays above the Flight Info drawer tab. And, if

you receive supplemental enroute data from your company, the fleet selection for

the supplemental data also displays above the Flight Info drawer tab.

Getting Started

Overview

About the Route List Button

Tapping the Route list button from the control bar while viewing Terminal Charts

shows and hides Chart Change Notices for the selected airport.

Tapping the Route list button while viewing the enroute map, provides access to

two tabs: the Route and Pubs tabs.

Route Tab

The Route tab provides access to the Route list which dynamically displays route-

based navigation objects that occur along the route corridor of your flight.

Navigation objects that elevate into the list include airspace, operational notes,

communication frequencies, waypoints, compulsory reporting points, and airports.

NOTE: FliteDeck Pro requires that two or more points are defined in the active

flight to display objects in the Route list.

Pubs Tab

From the enroute map, the Pubs tab provides access to Route Notes (Contin-

gency and Reference Notes), Jeppesen Airway Manuals, Enroute Change

Notices, and any Company Manuals.

 To show and hide the Route and Pubs tabs:

• Tap the Route list button from the control bar while viewing the enroute map.

The last viewed tab displays.

• Tap the Route tab to display the Route list.

• Tap the Pubs tab, from the Route list button to display publications.

About the Active Flight

The active flight is the displayed flight.It includes origin and destination airports,

any alternate airports, and the route description. The active flight also includes

any selected terminal charts associated with the flight. FliteDeck Pro displays the

name of the active flight on the Flight Info drawer tab.

Getting Started

Using the Toolba

Using the Toolbar

You access commonly performed tasks along the FliteDeck Pro toolbar.

FIGURE 2: FliteDeck Pro 3.0 Toolbar

Adjusting Display Brightness

The brightness button on the FliteDeck Pro toolbar controls the display brightness

of FliteDeck Pro and your iPad until your iPad goes to sleep or you power-off the

iPad.

 To adjust the display brightness:

1. Tap the Brightness button.

2. Slide the brightness control to decrease or increase the display brightness.

 To adjust the display for optimal viewing in low-light conditions:

1. Tap the Brightness button.

2. Switch Night Theme to ON.

Viewing GPS Status

Tap the GPS Status button to view current Ground Speed, Altitude, Last Position

Received, Accuracy status, and GPS Source. The minimum required GPS

accuracy to display ownship position is:

- 600 meters for the enroute map

- 200 meters for approach charts

- 200 meters for SID and STAR Charts

- 25 meters for taxi (10-9) charts

- 45 meters for the airport moving map

Getting Started

Using the Toolbar

GPS Loss Notification

FliteDeck Pro alerts you when minimum GPS accuracy requirements are not by:

• Displaying a badge on the GPS Status button

• Removing the ownship symbol from the map or chart

• Removing the Present Position button from the map

Performing a Search

Search is available from the FliteDeck Pro toolbar when you are viewing the

enroute map.

FliteDeck Pro searches for airports and fixes across all themes and the text of all

notes and Jeppesen Airway Manuals.

 To perform a search:

1. Tap the Search button while viewing the enroute map.

2. Enter text in the search field to begin a predictive search.

FliteDeck Pro begins searching after you enter two to three characters and

refines results as you type.

FliteDeck Pro indicates the number of results on the Search Results button

and highlights the objects that meet the search criteria on the map, in the

Route list, and in the Pubs tab.

3. Tap the Search Results button to display the Search Results popover.

FliteDeck Pro displays the Search Results popover with the All tab selected by

default - or the last viewed tab.

Text matching the search query in each category is highlighted. You might

need to tap See All for a category to view all search results in a specific

category.

4. Tap a search result from the list of search results.

FliteDeck Pro closes th search results popover, selects the object, centers the

viewable map area over the object, and displays details about the object.

Tap the X at the top of the details display to dismiss the details.

5. Tap the Cancel button next to the search field to clear any text in the Search

field and close the enroute search.

Getting Started

Using the Toolba

Accessing Settings

The Settings button provides access to data updates and FliteDeck Pro in-app

Help. It also provides controls for the display of the terrain legend; adjusting the

route corridor; changing a fleet for supplemental (tailored) enroute data, the

display of a terrain legend, and showing a taxi diagram on landing.

Performing Updates

When an update is available, a badge appears on the Settings button.

 To check the status of your data and perform updates:

1. Tap the Settings button.

2. Tap the Updates button.

FliteDeck Pro provides a status of your enroute, terminal, and manuals data.

3. To update data, when an update is available, tap the Update button at the

bottom of the screen.

See Managing Data Updates on page 78 for more information on performing data

updates.

Accessing Help

FliteDeck Pro in-app help is available to you at any time without the need for an

Internet connection.

 To access Help:

1. Tap the Settings button.

2. Tap the Help button and do one of the following.

• Tap in the Search field, enter a search query, and tap a topic from the

predictive search results.

• Tap a topic and subtopic from the list of Help topics.

3. Tap Done at the top of the Help window to dismiss the Help screen.

The Help button also displays Tech Support contact information.

Tapping the Tech Support on the Web button, with an Internet connection estab-

lished, opens the Jeppesen Customer Support Portal page for FliteDeck Pro. This

page contains training and documentation solutions, as well as hardware and

software compliance statements.

Adjusting the Route Corridor

The width of the route corridor determines how much information is elevated into

the Route list from the enroute map.

 To adjust the width of the route corridor:

1. Tap the Settings button.

Getting Started

Using the Toolbar

2. Tap the Route Corridor flyout.

3. Drag the slider to the right or left to adjust the width of the Default or Oceanic

route corridor.

See Working with the Route List on page 43 for more information.

Changing the Fleet Selection for Supplemental (Tailored)

Enroute Data

If your company provides supplemental enroute data, and you need to change the

fleet selection for the display of that data, you can do so from the Settings button.

 To change the fleet selection:

1. Tap the Settings button.

2. Tap the Fleet flyout.

3. Select another available fleet.

FliteDeck Pro displays the new fleet selection above the Flight Info drawer tab

and in global settings.

Hiding the Enroute Map Terrain Legend

When terrain is set to show, FliteDeck Pro overlays a small terrain legend on the

enroute map. There may be times when you need to view the enroute map

without the terrain legend overlaid on it.

 To hide the terrain legend from the enroute map:

1. Tap the Settings button from the FliteDeck Pro toolbar.

2. Switch Terrain Legend to OFF.

Showing the Taxi Diagram on Landing

The Show Taxi on Landing setting directs FliteDeck Pro to automatically switch to

the taxi diagram upon landing when your aircraft is moving no faster than the

speed specified in the Taxi on Landing Speed Threshold in FliteDeck Pro global

settings. See Automatically Displaying the Taxi Chart Upon Landing on page 73

for more information.

Locking the Display

Tap the Lock Display button to quickly lock and unlock the FliteDeck Pro display.

When the display is locked:

• The button is highlighted amber.

• You cannot access any other FliteDeck Pro buttons.

• You are prevented from panning or zooming from the current display.

• The Route list and moving map (if engaged) continue to be dynamic, but you

cannot interact with them.

Setting Up Your Flight

Creating a Route Manually

Setting Up Your Flight

You can setup your flight a number of ways in FliteDeck Pro. Once your route is entered, you can select

terminal charts to complete setting up your flight.

Creating a Route Manually

You can create a new flight and enter your route from within the Flight Info drawer

or by interacting with the enroute map.

 To create a new flight in the Flight Info drawer:

1. Tap the Flight Info drawer tab to open the drawer.

2. Tap the New Flight button and, if prompted, tap OK to confirm that you want

to continue.

NOTE: Starting a new flight removes your current route, airports, and

associated terminal chart selections.

3. Tap in the airport fields and enter the origin and destination airports using the

city name, airport ICAO, or IATA identifier.

After you enter characters in an airport field, when you tap into the next field, or

tap Done on the keyboard, FliteDeck Pro validates the airport name. You may

need to select the desired airport from a list.

4. Enter any alternate airports in the Alternate Airports field.

If you enter multiple alternates, separate each one with a space.

5. Once valid origin and destination airports are entered, you can use the SID

and STAR buttons to enter departure and arrival procedures, if available at

that airport. Follow the prompts to add runway and transition information.

6. You can tap in the route description box and enter any additional route points.

You can copy and paste route points into the route description box, you can

search for them using the Search tool, or you can insert them by interacting

with the map.

7. Tap Done on the keyboard.

8. Tap the Flight Info drawer tab to close the drawer. If you are viewing the

enroute map, you will see your new route depicted on the map.

NOTE: When you delete an origin or destination airport, the deleted airport is

automatically moved to the Alternate Airport field. FliteDeck Pro does this

to preserve any terminal chart selections or highlights you may have made

for the removed airport.

Setting Up Your Flight

Creating a Route Manually

Viewing SIDs and STARs Transition Points

FliteDeck Pro depicts transition points on the enroute map with a dashed line. A

label that identifies the procedure appears along the dashed line.

The display of ownship on SID and STAR charts is supported on geo-referenced,

or to-scale, SID and STAR charts only.

NOTE: FliteDeck Pro depicts SID and STAR transition points on the enroute map

to support situational awareness. Always brief the SID or STAR terminal

procedure.

About Route Points

Both plain language and dot-notation formats are supported in the route

description box. For example:

• N37 56.6 W122 21.4 SAC V23 RBL (plain language)

• N37.56.6.W122.21.4.SAC.V23.RBL (dot-notation)

Dot notation uses two dots to indicate direct-to points; and one dot between via

routings.

When you enter an airport as a route point in the description box, FliteDeck Pro

automatically includes the airport in the list of airports from the Airports button on

the control bar.

About Latitude and Longitude Coordinate Formats

The following latitude and longitude coordinate formats are supported in the route

description box:

• NxxWxxx (N37W122)

• Nxx.x Wxxx.x (N37.5 W122.2)

• Nxx xx.x Wxxx xx.x (N37 56.6 W122 21.4)

• Nxx xx.xx Wxxx xx.xx (N37 56.60 W122 21.40)

• NxxxWxxxx (N375W1222)

• N xx xx W xxx xx (N 37 56 W 122 40)

• XXXXN (5275N)

• XXNXX (75N70)

• XXNXXXW (37N122W)

Editing Your Route in the Flight Info Drawer

You can quickly edit your route from within the Flight Info drawer or from the

enroute map.

Setting Up Your Flight

Creating a Route Manually

 To edit your route from within the Flight Info drawer:

1. Tap the Flight Info drawer tab to open the drawer.

2. Complete any of the following actions:

• To add, delete, or edit airports, tap in the origin, destination, or alternate

airport fields and edit the information.

• To add, delete, or edit any of the route points for the active flight, tap in the

route description box and edit the route description.

3. Tap Done on the keyboard.

NOTE: When you delete an origin or destination airport, the deleted airport is

automatically moved to the Alternate Airport field. FliteDeck Pro does this

to preserve any terminal chart selections or highlights you may have made

for the removed airport.

Editing Your Route by Interacting with the Map

Sometimes the quickest way to edit your route is to directly interact with the

enroute map.

To edit your route by interacting with the map:

1. Touch, hold, and release a point or object along your intended route.

FliteDeck Pro displays additional information for that object.

2. Depending on the object selected, create a user waypoint, review additional

information, or select the object to add it to or remove it from your route.

NOTE: The Direct To option is available when Moving Map in FliteDeck Pro global

settings is enabled and the minimum GPS accuracy requirement is met.

Rubber-Band Routing

Another simple way to edit your route is to use the rubber-band functionality.

 To edit your route by using rubber-band routing:

1. Touch, hold, and a point along the existing route line.

FliteDeck Pro displays a point along the route line.

2. Drag the route line with your finger to the point that you want to add to the

route and release. After you release your finger, select the action that you want

to perform.

Setting Up Your Flight

Creating a Route Manually

Working with User Waypoints

You can quickly create temporary waypoints used for a single instance in your

route. FliteDeck Pro displays temporary user waypoints on the enroute map with a

star symbol inside a box.

You can also just as easily create permanent waypoints used for reference points,

which may or may not be part of your route. FliteDeck Pro depicts permanent user

waypoints on the enroute map with a star symbol.

About User Waypoints

These are several types of user waypoints that you can create:

• Latitude/Longitude User Waypoints—you can create these user waypoints

quickly by tapping the map once, and then selecting Done. They are

represented on the enroute map by their coordinates.

• Radial DME User Waypoints—the location of these waypoints is based on the

radial DME that you enter in the Name field. They are represented on the

enroute map by the Radial DME names.

• Named User Waypoints—create these waypoints to name a point for easier

recognition and recall. They are represented on the enroute map by their

names.

User waypoints that are part of a route are shared along with shared flights

between iPads and are available in all enroute themes and zoom scales.

You can search for user waypoints by it’s user-defined name, radial DME, or

latitude/longitude coordinates.

Creating Temporary User Waypoints

You can create and edit temporary user waypoints by interacting with the enroute

map.

 To create a temporary user waypoint:

1. Touch, hold, and release the enroute map at the location where you want to

insert the waypoint.

FliteDeck Pro displays New Waypoint details.

2. For the Name field, do one of the following:

• If you are creating a temporary latitude/longitude user waypoint, leave

empty.

• If you are creating a radial DME user waypoint, in the Name field, enter the

radial DME in this format: Navaid, Radial/DME.

For example, for "Direct to 26 DME on 156 radial off of Falcon VOR,"

you would enter VOR ident, radial/DME: FQF156/26

Setting Up Your Flight

Creating a Route Manually

Radials must be entered using three digits with a forward slash between

the radial and the DME, and must not include any spaces.

• If you are creating a named user waypoint, in the Name field, enter the

name.

3. To enter comments, tap in the Comments field and enter any comments.

4. Complete the action by doing one of the following:

• Tap Add to Route to add the waypoint to the current route. You might need

to designate the point from which you want to add the user waypoint.

• Tap Direct To to add the waypoint to the current route and remove all points

between the ownship position and the waypoint.

FliteDeck Pro displays the star symbol with a box around it for the newly created

temporary user waypoint on the enroute map.

NOTE: The Direct To option is available when the Moving Map setting in

FliteDeck Pro global settings is set to ON and the minimum GPS accuracy

requirements are met.

Creating Permanent User Waypoints

You can create and edit permanent user waypoints by interacting with the enroute

map.

 To create a permanent user waypoint:

1. Touch, hold, and release the enroute map at the location where you want to

insert the waypoint. FliteDeck Pro displays New Waypoint details.

2. For the Name field, do one of the following:

• If you are creating a permanent latitude/longitude user waypoint, leave

empty.

• If you are creating a permanent radial DME user waypoint, in the Name

field, enter the radial DME in this format: Navaid, Radial/DME.

For example, for "Direct to 26 DME on 156 radial off of Falcon VOR,"

you would enter VOR ident, radial/DME: FQF156/26

Radials must be entered using three digits with a forward slash between

the radial and the DME, and must not include any spaces.

• If you are creating a named user waypoint, in the Name field, enter the

name.

3. To enter comments, tap in the Comments field and enter any comments.

4. Tap Done at the top of the New Waypoint details.

Setting Up Your Flight

Creating a Route Manually

FliteDeck Pro displays the star symbol for the permanent user waypoint on the

enroute map.

Switching a Temporary User Waypoint to Permanent

 To switch a temporary user waypoint to a permanent user

waypoint:

1. Touch, hold, and release the temporary user waypoint. FliteDeck Pro displays

the waypoint details.

2. Switch Delete When Route is Cleared to OFF.

3. Tap Done at the top of the Waypoint details.

FliteDeck Pro displays the star symbol for the permanent user waypoint on the

enroute map.

Adding a Permanent User Waypoint to Your Route

 To add a permanent user waypoint to your route:

1. Touch, hold, and release the permanent user waypoint. FliteDeck Pro displays

the Waypoint details.

2. Complete the action by doing one of the following:

• Tap Add to Route to add the waypoint to the current route.

You might need to designate the point from which you want to add the user

waypoint.

• Tap Direct To to add the waypoint to the current route and remove all

points between ownship position and the waypoint.

Removing a Permanent User Waypoint from your Route

 To remove a permanent user waypoint from your route:

1. Touch, hold, and release the user waypoint. FliteDeck Pro displays the

Waypoint details.

2. Tap the Remove from Route button and confirm the deletion.

• If it is a permanent user waypoint, FliteDeck Pro removes the user waypoint

from the route, but it is not deleted from the map.

• If it is a temporary user waypoint, FliteDeck Pro removes the user waypoint

from the route, and it is no longer available on the map.

Setting Up Your Flight

Creating a Route Manually

Deleting User Waypoints

A permanent user waypoint must be deleted manually.

 To delete a permanent user waypoint:

1. Touch, hold, and release the waypoint you want to delete. FliteDeck Pro

displays the Waypoint details.

2. Tap the Delete (trashcan) button at the top of the Waypoint details and then

confirm the deletion.

FliteDeck Pro deletes the permanent user waypoint from the enroute map.

Direct To Routing

Direct To routing is available to you when Moving Map in FliteDeck Pro global

settings is set to ON and your GPS accuracy is 200 meters or better.

FIGURE 3: Route with 10 points in the route.

When you select Direct To for a point that is not in your route, FliteDeck Pro

directs you to the new Direct To point from your present position. FliteDeck Pro

then directs you to the next point in your route. For example, when you select

Direct To point A after point 3, FliteDeck Pro directs you from present position to

point A, and then to point 4 in your route.

Setting Up Your Flight

Creating a Route Manually

FIGURE 4: Direct To Point A

When you select Direct To for point 8 after point 3, FliteDeck Pro retains Origin

and points 1,2,3 and points 8,9,10, and Destination.

FIGURE 5: Direct To Point 8

When you select Direct To for a new destination, an airport, for example, all points

from your present position to the new destination are removed. All points already

flown from the Origin are retained.

When you select Direct To for a new destination, an airport, for example, all points

from your present position to the new destination are removed. All points already

flown from the Origin are retained.

Setting Up Your Flight

Creating a Route Manually

For example, when you select Direct To a new destination starting after point 3,

Origin and points 1,2,3 are retained, and there is a direct line from your present

position to the new destination.

FIGURE 6: Direct To a New Destination

NOTE:

If you change your route in flight, FliteDeck Pro takes one minute per

waypoint 'flown' to catch up to where you are at the present position. (For

example, 5 points = 5 minutes).

If you do not wait that one minute per waypoint, all points from the Origin

to the Direct To point, and then all points from the Direct To point to the

Destination are removed.

FIGURE 7: All Points Removed between Origin and Direct To Point and Direct To

Point and Destination

Setting Up Your Flight

Working with Saved Flights

You can quickly set up your flight by loading a saved flight.

FIGURE 8: Accessing Saved Flights

Loading a Saved Flight

A saved flight can include origin and destination points, alternate airports, the

route description, and any selected terminal charts that are associated with the

flight.

 To load a saved flight:

1. Tap the Flight Info drawer tab to open the drawer.

2. Tap the Saved Flights button.

3. Tap a saved flight from the list of saved flights to expand its view.

4. Tap the Load button next to the saved flight that you want to load.

FliteDeck Pro loads the flight information into the Flight Info drawer and the

flight becomes the active flight.

Saving the Active Flight

Saving the active flight is as easy as two taps.

To save an active flight:

1. Tap the Flight Info drawer tab to open the drawer.

2. Tap the Save button at the top of the Flight Info drawer.

FliteDeck Pro adds the flight to your list of Saved Flights each time you tap

Save.

Setting Up Your Flight

Working with Saved Flights

Duplicating a Saved Flight

Duplicating a saved flight can save time. For example, when you want to plan for

two different scenarios for the same airport pair.

You can create the flight, select your charts, and save the flight. Then, duplicate

the saved flight and make any changes to the duplicated flight to reflect the

second scenario.

 To duplicate a saved flight:

1. Tap the Flight Info drawer tab to open the drawer.

2. Tap the Saved Flights button.

3. Swipe to the left over the flight that you want to duplicate.

4. Tap Duplicate.

FliteDeck Pro duplicates the saved flight and adds it to your list of Saved Flights.

FIGURE 9: Duplicating a Saved Flight

Sorting Saved Flights

By default, saved flights are sorted by date. They can also be sorted by name.

 To sort Saved Flights:

1. Tap the Flight Info drawer tab to open the drawer.

2. Tap the Saved Flights button.

3. Tap the Sort by field and select either:

• Date Updated

• Flights by Name

Deleting Saved Flights

Deleting a flight is as easy as duplicating one.

 To delete a saved flight:

1. Tap the Flight Info drawer tab to open the drawer.

2. Tap the Saved Flights button.

3. Swipe to the left over the flight you want to delete.

4. Tap Delete.

Setting Up Your Flight

Working with Shared Flights

You can set up your flight by loading a shared flight.

To share flight information between two iPads, make sure that both iPads are

running FliteDeck Pro and have Allow Flight Sharing set to ON in FliteDeck Pro

global settings. FliteDeck Pro uses either a Bluetooth or Wi-Fi connection to share

flight information. Ensure these settings are set to ON.

Loading a Shared Flight

Whenever you receive a request to share flight information from another iPad, or

app on your iPad, FliteDeck Pro displays a notification. .

FIGURE 10: Sharing flight information notification on receiving iPad

 To load a shared flight:

• Tap Load, Save, or Decline.

- Load replaces any current active flight with the shared flight in the Flight

Info drawer.

- Save adds the shared flight to your list of Saved Flights.

- Decline rejects the shared flight.

FliteDeck Pro returns to the sending iPad running FliteDeck Pro a notification

that the flight info was either successfully shared or declined.

Sharing an Active Flight

A shared flight includes route airports, route description, and any selected

terminal charts associated with the flight.

 To share an active flight:

1. Tap the Flight Info drawer tab to open the drawer.

2. Tap the Share button.

3. From the list of nearby devices or apps, select the one with which you want to

share.

FliteDeck Pro returns a notification that the flight info was either successfully

shared or declined.

Setting Up Your Flight

Working with Flight Plan Routes

Sharing a Saved Flight without Loading It

You can also share a saved flight without loading it as the active flight in your

Flight Info drawer.

 To share a saved flight without loading it:

1. Tap the Flight Info drawer tab to open the drawer.

2. Tap the Saved Flights button.

3. Tap a saved flight to expand its view.

4. Tap Share next to the flight you want to share without loading it as the active

flight.

5. From the list of nearby devices or apps, select the one with which you want to

share.

What is Shared Between iPads

When you share flight information from one iPad to another, the following is

shared:

• Origin, destination, and any alternate airports

• Navaids, waypoints (including user waypoints), and airways

• Selected terminal charts for the flight

NOTE: Both iPads must include the terminal chart coverage area for the selected

terminal chart to successfully share the selected charts from device to

device.

What is Not Shared Between iPads

When you share flight information from one iPad to another, the following are not

shared:

• Highlights on terminal charts or AMM

• Rotated view of terminal charts

• Comments associated with a user waypoint

• Customized filter settings for enroute map objects

Working with Flight Plan Routes

You can enter a route by loading a route from a flight-planning system that is set

up to share with FliteDeck Pro.

NOTE: To load a flight plan route, make sure that you have credentials entered in

Services > Flight Plans in FliteDeck Pro global settings and that an

Internet connection is established.

Contact your company administrator or Jeppesen account manager to

determine whether this option is available.

Setting Up Your Flight

Working with Flight Plan Routes

FIGURE 11: Loading a Flight Plan route

Viewing Flight Plan Routes

You can view and load flight plan routes in FliteDeck Pro. You can not send routes

back to the flight-planning system.

 To view flight plan routes:

1. Tap the Flight Info drawer tab to open the drawer.

2. Tap the Flight Plans button.

3. Enter the call sign of the aircraft, if required, and tap Done on the keyboard.

FliteDeck Pro lists routes under two headings: future ETD and past ETD.

• Future ETD: Pending flight plans that have an ETD up to six hours into the

future.

• Past ETD: Past flight plans that have an ETD within twenty four hours in the

past.

FliteDeck Pro displays the time and date that the list of flight plans was last

updated at the bottom of the list.

4.Tap the Refresh button at the bottom of the list to check for any updates.

FliteDeck Pro checks whether any updates have become available since you

last accessed the list flight plan routes and refreshes the list if there are are

any updates.

Loading a Flight Plan Route

A flight plan route includes origin, destination, any alternate airports, and the route

description, including any user waypoints. It does not include any selected

terminal charts.

Setting Up Your Flight

Working with ATC-Cleared Routes

 To load a flight plan route into the Flight Info drawer:

1. Tap the desired flight plan to select it from the list of retrieved flight plan routes.

2. Tap the Load button next to the flight plan.

FliteDeck Pro loads the fight plan route into the Flight Info drawer as the active

flight.

Saving a Flight Plan Route Without Loading It

You can also save a flight plan route without loading it as the active flight in your

Flight Info drawer.

 To save a flight plan route without loading it:

1. Tap the desired flight plan to select it from the list of retrieved flight plan routes.

2. Tap the Save button next to the selected flight plan route.

FliteDeck Pro adds the flight plan route to your list of Saved Flights.

Working with ATC-Cleared Routes

You can quickly enter a route by loading an ATC-cleared route. ATC-cleared

routes are available for any flight within, into, or out of, the United States.

NOTE: To display ATC clearances, make sure that Display ATC Clearances is set

to ON in FliteDeck Pro global settings and that an Internet connection is

established.

FIGURE 12: Accessing ATC-cleared routes

Setting Up Your Flight

Working with ATC-Cleared Routes

Viewing ATC-Cleared Routes

You can view ATC-cleared routes for a city pair that has occurred in the last 24

hours.

 To View ATC-cleared routes:

1. After you enter origin and destination airports, tap the ATC Clearances button

in the Flight Info drawer.

FliteDeck Pro displays the time and date that the list was last updated appears

at the bottom of the list.

2. Tap the Refresh button at the bottom of the list to check for any updates.

FliteDeck Pro checks whether any updates have become available since you

last accessed the list of ATC-cleared routes and refreshes the list if there are

any updates.

Loading an ATC-Cleared Route

An ATC-cleared route includes origin, destination, any alternate airports, and the

route description, including any user waypoints. It does not include terminal

charts.

 To load an ATC-cleared route:

1. Tap the desired cleared route to select it from the list of ATC-cleared routes.

2. Tap the Load button next to the ATC-cleared route.

FliteDeck Pro loads the route into the Flight Info drawer as the active flight.

Saving an ATC-Cleared Route Without Loading It

You can also save a flight plan route without loading it as the active flight in your

Flight Info drawer.

 To save an ATC-cleared route without loading it:

1. Tap the desired cleared route to select it from the list of ATC-cleared routes.

2. Tap the Save button next to the ATC-cleared route.

FliteDeck Pro adds the route to your list of Saved Flights.

Setting Up Your Flight

Selecting Terminal Charts for Your Flight

At any point after you enter an airport, you can preview and select terminal charts

for your route airports.

Selecting Terminal Charts for the Active Flight

When you create a new flight, FliteDeck Pro automatically selects the airport

diagram for the origin airport. A dot next to a chart category indicates that the

chart category contains a selected chart.

Whenever you tap a chart category with a selected chart, FliteDeck Pro displays

the last viewed, selected chart from that chart category.

 To preview and select charts:

1. Tap an available chart type button (REF, CO, STAR, APP, TAXI, or SID) from

the control bar.

FliteDeck Pro highlights the selected chart type category button and displays a

list of those charts for the selected airport.

2. To preview a chart, tap the chart title to view the chart.

FIGURE 13: Previewing a chart

3. To select a chart, tap the circle next to the chart title.

FliteDeck Pro places a check mark next to the selected chart and adds the

chart to the Selected Charts Bar at the bottom of the chart display area.

Setting Up Your Flight

Selecting Terminal Charts for Your Flight

About Chart Types

Chart type categories are:

• REF (Reference): Nonprocedural charts, sorted alphabetically by title.

• CO (Company): Company-tailored charts. This chart type is only available if

your company subscribes to Jeppesen tailored charting services.

Engine-Out (E/O) charts, when available, are displayed from the CO chart

type category.

• STAR (Standard Terminal Arrival): Arrival charts, sorted alphabetically by

title.

• APP (Approach): Approach charts, grouped by runway and sorted by index

number.

• TAXI: Taxi charts, sorted by index number.

NOTE: If your company subscribes to Airport Moving Map (AMM), you will also

have access to a toggle between Chart and AMM at the bottom of the taxi

chart area when AMM is available. These tabs allow you to navigate

between the two views. For more information on AMM, see Working with

the Airport Moving Map (AMM) on page 75.

• SID (Standard Instrument Departure): Departure charts, sorted alphabeti-

cally by title.

NOTE: There might be charts that are available to you that are non-Jeppesen-

sourced charts. In this case, FliteDeck Pro displays the text “Non-Jepp

Chart” in the chart list on the same line as the chart index number.

Ownship position does not display and the automatic switch to a taxi

diagram will not occur with non-Jeppesen-sourced charts.

Switching Between Route Airports

FliteDeck Pro identifies the selected airport on the Airport button.

 To switch between airports associated with the active flight:

1. Tap the Airports button on the control bar.

FliteDeck Pro displays a list of the Route Airports.

2. Tap an airport from the list to select the airport for which you want to view and

select terminal charts.

Setting Up Your Flight

Selecting Terminal Charts for Your Flight

Navigating Between Selected Charts

Each selected terminal chart is represented by a pagination dot on the Selected

Charts bar which is located under the chart display area.

 To navigate between selected charts, you can:

• Swipe two fingers to the left or right to cycle through selected charts.

• Tap outside on the left or right side of the selected charts bar to move to the

previous or next chart.

• Tap the chart type button to jump across multiple selected charts.

Associating an Engine-Out Chart with a SID

When there is an engine-out (E/O) chart available, FliteDeck Pro prompts you to

associate it with the SID when you select the departure.

To associate an E/O chart with a departure:

1. Tap the SID chart type button.

FliteDeck Pro displays a list of departure charts.

2. Select the departure chart by placing a check mark next to it.

If any E/O charts are associated with the selected departure, FliteDeck Pro

displays an Associate Engine-Out Chart popover.

3. Tap the desired E/O chart from the list of charts.

4. Tap the OK button.

FliteDeck Pro dismisses the popover, and displays an amber E/O button

under the Chart Type buttons.

NOTE: Each selected departure can be associated with no more than one E/O

procedure. However, the same E/O procedure can be associated with

multiple departures.

Displaying an Engine-Out Chart

When an engine-out chart is available and associated with a SID, FliteDeck Pro

displays an amber E/O button under the chart category buttons.

 To display an E/O chart:

• Tap the amber E/O button.

FliteDeck Pro displays the associated E/O chart.

Setting Up Your Flight

Viewing Manuals and Change Notices

Finally, as part of setting up your flight, you may want to review Manuals, and

check for any relevant change notices along your route. This is all possible from

the Route list - Pubs tab.

FliteDeck Pro provides access to Jeppesen Airway Manual text, Company

Manuals, as well as Enroute and Chart Change Notices from the Pubs tab.

FIGURE 14: Displaying the Pubs tab while viewing the Enroute Map

Pubs Tab from the Enroute Map

Tapping the Route list button and Pubs tab while viewing the enroute map returns

you to your last view in the Pubs tab. You might need to tap the [ < ] Back button

until you return to the top of the list of publications.

At the top level of Pubs information, the Pubs tab provides access to Route Notes,

fully indexed and searchable Jeppesen Airway Manual text by region, and

company manuals.

Route Notes

Tapping the Route Notes flyout from the Pubs tab displays any Contingency or

Reference Notes along your route elevated into the list from Jeppesen Airway

Manual text.

Airway Manual Text - Regions

Tapping a region from the Pubs tab provides access to Enroute Change Notices,

General Airway Manual text, and the Jeppesen Airway Manual text for the region

you selected. The magenta line indicates your current region.

Setting Up Your Flight

Viewing Manuals and Change Notices

Jeppesen Airway Manual text is fully indexed and searchable. See Viewing

Jeppesen Airway Manuals on page 49 for more information.

Enroute Change Notices

Tapping the Enroute Change Notices flyout provides access to Enroute Change

Notices by region.

NOTE: Enroute Change Notices highlight significant changes affecting the

enroute area environment that may be utilized by your aircraft flight

management system. Entries are published until the temporary condition

no longer exists, or until the permanent change is made to the database.

See Viewing Enroute Change Notices on page 50 for more information.

Company Manuals

Company Manuals are provided to you by your company in PDF format and, as a

result, the text is not indexed or searchable from within FliteDeck Pro.

See Viewing Company Manuals on page 51 for more information.

Pubs Tab from Terminal Charts View

Tapping the Route list button while viewing terminal charts, provides you with

access to Chart Change Notices for the selected airport. In addition, with an

established Internet connection, you can also access the most recent change

notices by tapping the jeppesen.com link at the bottom of the list.

Setting Up Your Flight

Viewing Manuals and Change Notices

ccessing Enroute Information

djusting the Enroute Map View

Accessing Enroute Information

FliteDeck Pro not only allows you to filter map objects to customize your view of the enroute map, it also

elevates route-based information along your route, minimizing your need to interact with the app during flight.

Adjusting the Enroute Map View

Viewing your flight with respect to the enroute air structure improves situational

awareness.

About Enroute Map Themes

FliteDeck Pro provides access to three enroute themes to view the map with.

• High IFR: provides aeronautical information to facilitate enroute instrument

navigation, generally above FL180.

• Low IFR: provides aeronautical information to facilitate enroute instrument

navigation, generally below FL180.

• VFR: provides aeronautical information for conducting flight under visual flight

regulations in the United States and parts of Europe.

NOTE: To display the VFR enroute theme, ensure that Display VFR Theme in

FliteDeck Pro global settings is set to ON.

Switching Enroute Map Themes

 To change to the enroute map from viewing terminal charts:

• Tap the Enroute Theme button on the control bar.

FliteDeck Pro switches to the enroute map view displaying the enroute theme

that is labeled on the enroute theme button.

 To change enroute themes while viewing the enroute map:

1. From the enroute map, tap the Enroute Theme button.

2. Tap the enroute theme you want to display: High IFR, Low IFR, or VFR.

NOTE: When you change to another enroute theme, certain route objects might

not be included in the theme that you change to. In that case, FliteDeck

Pro displays the object as a standard waypoint on the enroute map. When

you switch back to the theme that includes the object, FliteDeck Pro

displays the object as it was originally defined.

For example, if you add a VFR checkpoint to your route from the VFR

enroute theme, and then switch to the Low IFR enroute theme, FliteDeck

Pro displays the checkpoint with a standard waypoint symbol.

Accessing Enroute Information

Adjusting the Enroute Map View

Displaying Ownship on the Enroute Map

For those authorized to display ownship in flight, current ownship position is

available on the enroute map when both the Moving Map and Display Ownship

settings in the Enroute View section of FliteDeck Pro global settings are set to ON

and GPS accuracy requirements are met.

NOTE: Centering the map over aircraft position and displaying the ownship

symbol on the enroute map are actions designed to improve situational

awareness during enroute flight. These functions are not to be used as the

basis for navigation.

Moving Map

You can view enroute Moving Map without displaying ownship by switching only

Moving Map (and not Display Ownship) to ON in FliteDeck Pro global settings.

In this case, the map moves along with ownship position, and the Present Position

and Map Orientation buttons are still available - just without the display of

ownship.

Viewing Present Position

 To recenter the map over ownship position after you have panned

away:

• Tap the Present Position button from the enroute map.

The Present Position button is only available on the enroute map when Moving

Map in FliteDeck Pro global settings is set to ON, you have panned the map

away from current ownship position, and GPS accuracy requirements are

met..

NOTE: When enroute Moving Map is enabled, any action that pans the map stops

it from moving. Tapping the Present Position button on the enroute map

resumes the moving map.

Switching Map Orientation

 To change the enroute map orientation:

• Tap the North Up or Track Up button on the enroute map to switch

between orientations.

NOTE: The Track Up button is only available on the enroute map when Moving

Map in the Enroute View of FliteDeck Pro global settings is set to ON and

GPS accuracy is better than 200 meters.

ccessing Enroute Information

djusting the Enroute Map View

Viewing Distance

The distance measuring tool displays a set of rings or arcs that you can use to

view distance on the enroute map.

 To show and hide the rings or arc:

• Tap the Distance Measuring Tool button.

As you zoom in or out on the map, the rings change with the map scale. The

center-most ring includes a compass rose that indicates true north, south,

east, and west.

Determining Distance with the Offset Indicator

 To determine the distance an object on the map is to ownship

position:

1. Tap the Distance Measuring Tool button to show the range rings or arcs.

2. Pan the map so that the map object in question is in the center of the inner

range ring.

FliteDeck Pro displays a magenta offset indicator, indicating distance and

direction to your aircraft position. If you switch the range rings off, the offset

indicator no longer appears.

You can determine the distance and direction of an object to your aircraft position,

when the Moving Map setting in the Enroute View section of FliteDeck Pro global

settings is set to ON and GPS accuracy requirements are met.

Accessing Enroute Information

Working with the Route List

The Route list, also referred to as Smart Notes, dynamically elevates route-based

navigation objects from the enroute map and filters it to the context of your flight -

minimizing your need to interact with the app during flight.

Key information in the route list includes: airspace; operational notes, such as

prior notifications, CPDLC logins; comm sector frequencies, and compulsory

reporting points.

All are presented as they occur along your route - filtered by direction, applicability

to specific FIR sectors, as well as entry and exit from a given airspace.

FIGURE 15: Showing the Route List

About the Route List

The top of the Route list corresponds with the beginning of your route.

Operational notes are numbered when the object to which they are associated

intersects with the route corridor. The numbers start with 1 at the origin and

increment in ascending order as you progress toward the destination. If you

modify your route, the Route list refreshes and any numbered notes along The top

of the Route list corresponds with the beginning of your route.

You can scroll the list by dragging your finger up and down the list. You can also

set the Route list to scroll along with the moving map by enabling Moving Map in

the FliteDeck Pro global settings.

When the list scrolls, objects within a FIR boundary slide up underneath the FIR

row in the list. When the last object for that FIR scrolls under the FIR, the next FIR

scrolls to the top.

NOTE: With Moving Map enabled and GPS minimum requirements met,

FliteDeck Pro scrolls the Route list along with the moving map. Any

permanent user waypoint or object that intersects with the route corridor

ccessing Enroute Information

Working with the Route List

that has an operational note associated with it will also be identified in the

Route list with an Off Route label.

Showing and Hiding the Route List

To display information in the Route list, you need to enter two or more points in

the Flight Info drawer.

 To show and hide the Route list:

1. Tap the Route list button from the FliteDeck Pro control bar while viewing the

Enroute map.

FliteDeck Pro displays two tabs when you tap the Route list button from the

enroute map: Route and Pubs. FliteDeck Pro opens to the last viewed tab.

2. Tap the Route tab, if it is not already selected.

To collapse and expand the Route list, swipe the handle at the bottom of the

list up and down.

Viewing the Route List with Moving Map

When Moving Map is set to ON in FliteDeck Pro global settings, the Route list

scrolls as the ownship position passes over navigation objects on the map.

As the ownship position passes over an object in the Route list (such as

waypoints, navaids, etc.), that object slides under the FIR.

When Moving Map and Display Ownship are both set to ON and the GPS

accuracy is 200 meters or better, FliteDeck Pro indicates the next active waypoint

along your route with a vertical magenta line.

NOTE: When Moving Map is enabled, any action that pans the map stops it from

moving. Tapping the Present Position button from the enroute map

resumes the moving map.

Adjusting the Route Corridor

The route corridor is the shaded area on each side of your route that is displayed

in the Route list.

The width of the route corridor determines how much information displays in the

Route list. When the corridor is wider, more notes and route-based information

appear in the Route list. When the corridor is narrower, fewer notes and less

route-based information appear in the Route list.

Accessing Enroute Information

Working with the Route List

NOTE: The route corridor changes from Default (10 NM each side of the route) to

Oceanic (25 NM each side of the route) at and along FIR/UIR boundaries.

FIGURE 16: Route Corridor Change shown in Route list and on enroute map

 To resize the width of the route corridor:

1. Tap the Settings button from the FliteDeck Pro toolbar.

2. Tap the Route Corridor flyout.

3. Slide the bar to the right or left to adjust the setting. Values range from 0 to 100

NM over land, and 0 to 200 NM over ocean.

You can adjust the route corridor with or without an active flight in the Flight Info

drawer.

NOTE: The route corridor changes from Default to Oceanic at and along FIR/UIR

boundaries.

ccessing Enroute Information

Working with the Route List

Viewing Object Details from the Route List

Viewing map objects from the Route list is as simple as tapping the object. And

just like when tapping an object from the map, the details available when tapping

an object in the Route list depends on the type of object selected.

FIGURE 17: Route List with Operational Note Details

 To view more details about any item in the Route list:

1. Tap the object in the Route list.

FliteDeck Pro selects the object on the map, and displays more details about

the object.

2. Tap the X at the top of the details display to dismiss it and return to the Route

list.

Changing the Display of Communication Frequencies

FliteDeck Pro displays FIR communication frequencies in the Route list using the

first two ACC frequencies by default. For Airports, FliteDeck Pro displays the ATIS

frequency by default.

 To change FIR or airport communication frequencies that display

in the Route list:

1. Tap the Airport or FIR communications flyout in the Route list.

2. Tap See All for a complete list of frequencies. FliteDeck Pro expands the list of

frequencies.

Accessing Enroute Information

Working with the Route List

3. Scroll the list and tap the desired frequency in the list. FliteDeck Pro places a

check next to the selected frequency.

FIGURE 18: List of FIR communication frequencies

4. Tap the X at the top of the popover to dismiss it and display the Route list

again.

FliteDeck Pro refreshes the frequencies that appear in the Route list.

Searching the Route List

 To search the Route list:

1. With the Route list open, tap the Search button from the FliteDeck Pro toolbar.

2. Enter text in the search field to begin a predictive search.

FliteDeck Pro begins searching after you enter two characters and refines

results as you type.

3. When FliteDeck Pro indicates the number of results on the Search Results

button and highlights objects matching the search query in the Route list, you

can do one of the following:

• Scroll the Route list and tap the highlighted search result from the Route

list.

Any object or text that meets the search query highlights in the Route List. If

text matching the search query is in the body of a note, the matching text

surfaces in the Route list for that note.

ccessing Enroute Information

Working with the Route List

• Tap the Search Results button and refine the results by tapping a category

tab.

FIGURE 19: Search query matching text in body of a note

When you tap a search result, FliteDeck Pro closes the search results

popover, selects the object, centers the viewable map area over the object,

and displays details about the object.

4. Tap the X at the top of the details display to dismiss the details.

5. Tap the Cancel button on the FliteDeck Pro toolbar to clear any text in the

Search field and close the enroute search.

Accessing Enroute Information

Working with Publications

From the enroute map, you have access to Jeppesen Airway Manual text, Route

Notes (Contingency and Reference Notes), Enroute Change Notices, and

Company Manuals.

Viewing Jeppesen Airway Manuals

FliteDeck Pro provides fully indexed and searchable Jeppesen Standard Airway

Manual text.

 To view Jeppesen Airway Manual text:

1. Tap the Route list button while viewing the enroute map, if the Route list is not

already open.

2. Tap the Pubs tab, if it is not already selected.

At the top level of Pubs information, the Pubs tab provides access to Route

Notes, Jeppesen Airway Manual text by region, and company manuals.

You might need to tap the [ < ] Back button until you return to the top of the

list of Pubs.

3. Tap the desired flyout from the list of regions.

The magenta line indicates your current region.

4. Under Documents, tap the desired Airway Manual text flyout.

5. Scroll through the list Airway Manual topics, and tap the desired flyout.

6. Tap the desired title from the list of subtopics.

FliteDeck Pro opens the content viewer opens and displays the content.

• You can zoom and scroll the content, or you can tap the Expand Content

button to expand the content viewer to full screen.

• You can swipe the handle up and back down from the bottom of the content

viewer to view the information and the map.

ccessing Enroute Information

Working with Publications

• To close the content viewer, tap the X at the to p of the display.

FIGURE 20: Pubs tab > Pacific Region > Pacific Airway Manual > Enroute Data-

Pacific > Australian Organized Track Structure (AUSOTS)

Viewing Enroute Change Notices

Enroute Change Notices highlight significant changes affecting Jeppesen

navigation data that may be utilized by your aircraft flight management system.

Entries are published until the temporary condition no longer exists, or until the

permanent change is made to the database.

 To view Enroute Change Notices:

1. Tap the Route list button while viewing the enroute map, if the Route list is not

already open.

2. Tap the Pubs tab, if it is not already selected.

FliteDeck Pro displays a list of publications for the last viewed category of

information. You might need to tap the [ < ] Back button until you return to a

list of publications.

3. Tap the desired flyout from the list of regions.

The magenta line indicates your current region.

4. Under Documents, tap Enroute Change Notices.

5. Tap the desired title from the list of Enroute Change Notices.

FliteDeck Pro opens the content viewer and displays the content.

• You can zoom and scroll the content, or you can tap the Expand Content

button to expand the content viewer to full screen.

• You can swipe the handle up and back down from the bottom of the content

viewer to view the information and the map.

Accessing Enroute Information

Working with Publications

• You can view the content in another app on your iPad by tapping the Share

button.

• To close the content viewer, tap the X at the top of the display.

FIGURE 21: Pubs tab > Pacific Region > Enroute Change Notices > EFB-PACIFIC

On Demand Change Notices

You can view the most recent change notices by tapping the jeppesen.com link

at the bottom of the Enroute Change Notices display. On Demand Change

Notices are updated on a daily basis and provide an option for you to search for a

single airport or FIR.

NOTE: Always check for pertinent NOTAMs prior to flight.

Viewing Company Manuals

If your company subscribes to Jeppesen document management services, your

company documents may also be available from the Pubs tab.

 To view a company document:

1. Tap the Route list button while viewing the enroute map, if the Route list is not

already open.

2. Tap the Pubs tab, if it is not already selected.

FliteDeck Pro displays a list of publications for the last viewed category of

information. You might need to tap the [ < ] Back button until you return to a

list of publications.

3. Tap the Company Manuals flyout.

4. Tap a manual to select from the list of company documents.

FliteDeck Pro opens the content viewer and displays the content.

• You can zoom and scroll the content, or you can tap the Expand Content

button to expand the content viewer to full screen.

• You can swipe the handle up and back down from the bottom of the content

viewer to view the information and the map.

ccessing Enroute Information

Working with Publications

• You can view the content in another app on your iPad by tapping the Share

button.

• To close the content viewer, tap the X at the top of the display.

NOTE: You can use a four-finger swipe to move between another application and

the FliteDeck Pro app.

Viewing Route Notes

Not all notes are associated with a boundary or navigation object and appear in

the Route list.

Route Notes, which are a combination of contingency and reference notes

relevant to your route, are available to you from the Pubs tab.

• Contingency notes provide information, plans or procedures to adhere to in the

case of an in-flight emergency or other unexpected event such as severe

weather and other Air Traffic situations.

In prior FliteDeck Pro releases, these notes were available from the Reference

tab from the Notes popover. On pre-composed, paper enroute charts, these

notes are available on the end panels.

• Reference notes are more generic in nature and provide procedural and

reference information, or acts as a pointer to the Jeppesen Airway Manual text

pages.

In prior FliteDeck Pro releases, these notes were also available from the

Reference tab from the Notes popover. On pre-composed, paper enroute

charts, these notes are available on the end panels.

 To view Route Notes:

1. Tap the Route list button while viewing the enroute map, if the Route list is not

already open.

2. Tap the Pubs tab, if it is not already selected.

FliteDeck Pro displays a list of publications for the last viewed category of

information. You might need to tap the [ < ] Back button until you return to a

list of publications.

3. Tap the Route Notes flyout.

FliteDeck Pro displays a list of Contingency and Reference Notes.

4. Tap a note to select it.

Accessing Enroute Information

Working with Publications

FIGURE 22: Pubs tab > Route Notes > Contingency- SPECIAL PROCEDURES FOR

INFLIGHT CONTINGENICES IN OCEANIC AISPACE - PACIFIC

FliteDeck Pro opens the content viewer and displays the note.

• For longer notes, you can scroll the note, or you can tap the Expand

Content button to expand the content viewer to full screen.

• You can also swipe the handle up and back down from the bottom of the

content viewer to view the note and the map.

• To close the content viewer, tap the X at the top of the display.

NOTE: You can access Contingency and Reference notes from the Pubs tab with

or without a route entered by selecting a region and then scrolling the list.

Searching Publications

When you perform a search from the enroute map, FliteDeck Pro searches the

map, the Route list, and text in all notes and Jeppesen Airway Manuals. FliteDeck

Pro does not search text in company manuals.

 To search publications:

1. Tap the Route list button from the enroute map to open the Route list, if it is

not already open.

2. Tap the Pubs tab.

3. Tap the Search button from the FliteDeck Pro toolbar.

4. Enter text in the search field to begin a predictive search.

FliteDeck Pro begins searching after you enter three characters and refines

results as you type. FliteDeck Pro indicates the number of results on the

ccessing Enroute Information

Working with Publications

Search Results button, places a magenta dot next to any publication

containing the search query, and highlights the text contained in any note that

matches the search query.

5. To view the search results, tap the Search Results button and refine the

results by tapping the Pubs category tab.

FIGURE 23: Search Results - Pubs Tab

6. Scroll the list and tap a search result.

FliteDeck Pro displays the search result text in the content viewer.

7. Tap the Cancel button to clear any text in the Search field and close the

enroute search

Accessing Enroute Information

Viewing Enroute Map Object Details

You can learn more about any object on the map by doing one of the following:

• Short tapping on a map object directs FliteDeck Pro to select the object and

any associated notes, center the object in the viewable map area, and display

the object label. Tapping the selected object again will display more details

about the object and any notes.

• Long tapping on a map object is performed by touching, holding, and releasing

an object. This directs FliteDeck Pro to select the object on the map and any

associated notes, center the object in the viewable map area, and display

details about the object and any notes.

• Tap the X at the top of the details display to dismiss the details and deselect

the map object.

Depending on where you tap on the map, you may need to select from a list of

objects. The Back button at the top of the details display will return you to the list

of multiple objects.

Panning and zooming the map does not deselect the selected object.

NOTE: When the Route list is open, selecting a map object that is also in the

Route list will scroll that object’s FIR to the top of the Route list. If Moving

Map is enabled, selecting a map object, stops the moving map. Tapping

the Present Position button from the map resumes the moving map.

Viewing Airport Details

Tapping an airport from the map provides airport details including notes and

information on runways and communications for that airport. Airport details also

provide navigation to terminal weather, to any airport diagram for that airport, and

the ability to add or remove the airport from your route. Tapping Direct To

removes all route points between your current aircraft position and the selected

airport.

If your company provides supplemental enroute data for the airport, FliteDeck Pro

provides customized airport information from the Company Info flyout. For more

information, see Viewing Tailored Enroute Data on page 57.

NOTE: The Direct To option is available when Moving Map in the Enroute View of

FliteDeck Pro global settings is set to ON and GPS accuracy requirements

are met.

Viewing Airway Details

Tapping an airway from the map provides airway details including information on

outbound/inbound bearings, segment starts and ends, segment distances,

mileage between navaids, and any altitude requirements. Airway details also

provide access to cruise tables, and any restrictions.

In addition, if you are showing Organized Track Systems data on the map, tapping

a specific track provides details for that track. Track details include when the track

ccessing Enroute Information

Viewing Enroute Map Object Details

information is current, or future effective. When tracks expire, they are removed

from view. For more information, see Displaying Organized Track System Data on

page 64.

NOTE: FliteDeck Pro displays distances between VORs, changeover points, and

signal gaps on an airway when zoomed in to an appropriate zoom level.

Viewing VFR Route Details

FliteDeck Pro displays VFR routes on the map from the VFR enroute theme.

VFR routes include advisory routes, VFR flyways, military low flying routes,

military training routes, VFR transition routes-Europe, and VFR transition routes-

USA.

Viewing Fix and Waypoint Details

Tapping a waypoint provides information about the waypoint or enroute fix

including latitude/longitude coordinates, usage, and any intersection information.

It also provides you the ability to add it to or remove the waypoint from your route.

Tapping Direct To removes all route points between your current aircraft position

and the selected waypoint.

NOTE: The Direct To option is available when Moving Map in the Enroute View of

FliteDeck Pro global settings is set to ON and GPS accuracy requirements

are met.

Viewing Navaid Details

Tapping a navaid provides information including identifier, latitude and longitude

coordinates, station declination/magnetic variation, and type of navaid. It also

provides you the ability to add it to or remove it from your route. Tapping Direct To

removes all route points between your current aircraft position and the selected

navaid.

NOTE: The Direct To option is available when Moving Map in the Enroute View of

FliteDeck Pro global settings is set to ON and GPS accuracy requirements

are met.

Viewing Airspace Details

Class B airspace displays on the enroute map for both the origin and destination

airports entered in your route from all enroute theme views, High IFR, Low IFR

and VFR.

Tapping an airspace boundary provides details specific to the type of airspace

selected and any associated notes. FIR/UIR airspace includes altitude limits,

communications frequencies, and cruise levels.

In addition, if your company publishes ETOPS rings as part of their tailored

enroute data, you can view ETOPS rings on the map but you cannot tap them for

more details.

Accessing Enroute Information

Viewing Enroute Map Object Details

Viewing VFR Airspace Details

VFR airspace includes boundaries for Special Use Airspace (SUAA) and Special

Use Activity (SUAP).

VFR Special Use Airspace (SUAA) includes Flight Information Zones, Helicopter

Traffic Areas, Helicopter Traffic Zones, VFR Traffic Areas, Bird Areas, and Glider

Areas.

VFR Special Use Activity (SUAP) includes Bird Areas, Gas Venting Areas,

Intense Radio Areas, Parachute Areas, and Prohibited Overflight.

Viewing Terrain Details

You can hide the terrain legend by tapping the Settings button on the FliteDeck

Pro toolbar, and then switching Terrain Legend OFF.

Viewing Cultural Details

Cultural objects are available only from the VFR enroute theme. The Cultural

button controls showing and hiding city names, city patterns, high tension lines,

obstacles, railroads, and roads. VFR obstacles include buildings, towers, plants,

catenaries (suspended bridges), windmills, etc.

Viewing Operational Notes

Tapping a note symbol from the map (whether the note is part of your route and

numbered, or not a part of your route and not numbered) opens details for that

note. Notes are split into individual topics and display by type label.

When you are viewing IFR themes, FliteDeck Pro shows only IFR notes for all

objects in the respective IFR theme (high or low). When you are viewing the VFR

theme, FliteDeck Pro shows both VFR and IFR notes for all objects in the VFR

theme.

Viewing Tailored Enroute Data

Tailored Enroute is a solution available to your company to supplement Jeppesen

aeronautical data with company-specific enroute data.

Receiving Tailored Enroute Data

You can quickly identify whether you are receiving supplemental enroute data

from your company by the designation of a fleet above the Flight Info drawer tab.

You can also identify whether your company provides supplemental enroute data

from FliteDeck Pro global settings where your company name will be listed under

the Account Info >Tailored Enroute Data field.

You view the details of supplemental enroute data the same way that you view

details for any other object on the map. Tapping the object provides more details

ccessing Enroute Information

Viewing Enroute Map Object Details

about the object. The details depend on the type of object selected. You an also

filter for supplemental enroute data. For more information see, About Enroute

Map Filters on page 61.

Supplemental Enroute Map Objects include:

• Airports: Airports that have supplemental information provided for them are

shaded on the enroute map.

Tapping the airport selects the airport and displays airport details. If an airport

has supplemental information, FliteDeck Pro displays a Company Info flyout

from the airport details. Supplemental airport information is fleet-specific and

can include a list of company information related to the airport.

NOTE: FliteDeck Pro displays company airports designated as emergency

airports in red on the enroute map.

• Tailored Boundaries: Customized area boundaries are indicated on the

enroute map by shaded areas.

Tapping along the boundary selects the area and displays details about the

area. Examples of customized boundaries are No Fly Areas and Mountain

Wave Areas.

• Company Communications: shaded areas on the map can also indicate that

company communications frequencies are available for the area.

Designating a Fleet

When your company subscribes to and publishes supplemental enroute data, the

first time you launch FliteDeck Pro after supplemental enroute data has been

downloaded, you might be required to identify the fleet for which the supplemental

enroute data will be used. Fleets are defined and named by your company.

Accessing Enroute Information

Filtering Enroute Map Objects

FliteDeck Pro preserves the fleet selection until you change it, or it is removed

from the latest tailored enroute data set.

Changing the Fleet Selection

If you ever need to change the fleet selection for which supplemental enroute data

is received, you can do so from the Settings button on the FliteDeck Pro toolbar.

1. Tap the Settings button from the FliteDeck Pro toolbar.

2. Tap the Fleet flyout.

3. Select another available fleet.

FliteDeck Pro displays the new fleet selection on top of the Flight Info drawer tab.

Filtering Enroute Map Objects

FliteDeck Pro displays any object on the map that is a part of your route regardless of the filter setting, enroute

theme, or zoom level. for all other map objects, you can show and hide them to meet your needs.

Show and Hide Enroute Map Objects

To switch between showing and hiding enroute map objects, tap the corre-

sponding map object button.

• Airports

• Airways

• Waypoints

• Navaids

• airspace

• Terrain

• Cultural (VFR theme only)

Generally, the closer the zoom level, the more information is displayed on the

enroute map about an object.

The following table indicates the default settings that govern when enroute map

objects appear (if they are set to show) at specific zoom levels and enroute

themes.

Enroute Map Object High IFR Low IFR VFR

Airports 160 nm/in 80 nm/in 80 nm/in

Airways 80 nm/in 40 nm/in 40 nm/in

Organized Track Systems 640 nm/in 640 nm/in Never

Waypoints 20 nm/in 20 nm/in 20 nm/in

ccessing Enroute Information

Filtering Enroute Map Objects

TABLE 1: Enroute Map Object - Default Zoom Level Display

Customizing Enroute Map Object Filters

You can filter specific types of enroute map objects for an even more precise view

of the enroute map.

 To customize map filters:

1. From the enroute map, tap the Expand Filters Menu button to show the

object filters menu.

2. Tap the corresponding button for the object that you want to make adjust-

ments.

3. Make changes for the display of the object.

4. To close the menu, tap away from the filters menu or tap the Close Filters

Menu button.

NOTE: FliteDeck Pro displays an amber cue next to the button of an object that

you have changed the default filter setting.

About Enroute Map Filter Button States

FliteDeck Pro displays four different object button states:

• An amber cue indicates that a filter is applied to the object.

• Highlighted buttons indicate that the object is showing on the map.

• Gray buttons indicate that the object is available but not showing on the map.

Navaids 80 nm/in 40 nm/in 40 nm/in

Airspace 80 nm/in 40 nm/in 40 nm/in

Airspace (associated with

Tailored Enroute data)

320 nm/in 320 nm/in 320 nm/in

Terrain 200 nm/in 200 nm/in 200 nm/in

Cultural Information Never Never Always

Enroute Map Object High IFR Low IFR VFR

Accessing Enroute Information

Filtering Enroute Map Objects

• Dark gray buttons indicate that the object is not available at the current zoom

level or from the selected enroute theme.

NOTE: When you tap a map object button for an object that is not visible at the current

zoom level or enroute theme, the filters menu is still available for that object type.

About Enroute Map Filters

The filters available for each enroute map object are as follows:

• Airports

- Minimum Runway Length: This filter enables you to limit airports

displayed on the enroute map based on runway length.

- Show Only Company Airports: Filters the map to show only company

airports. This option is available only when your company provides

supplemental enroute data.

- Show Only ETOPs Airports: Filtering the map to show only ETOPs

airports is available only when your company provides this supple-

mental enroute data.

- Filter Airports by Services: Filters the map to show only company airport

based on the services you select. These services include Medical, Gate,

and mechanical. This option is available only when your company

provides supplemental enroute data.

- Show Airports at all Scales: If your company has enabled this option,

you can customize your view to show airports at all scales regardless of

the map zoom level.

- In the VFR theme, you can specify whether to show or hide heliports,

seaports, and private airports.

• Airways

- When Display Organized Track Systems is set to ON in FliteDeck Pro

global settings, you can filter Show Organized Tracks ON or OFF when

ccessing Enroute Information

Filtering Enroute Map Objects

viewing the map in either IFR enroute themes.

FliteDeck Pro displays the last time that Organized Track System data

was updated.

If you filter Show Organized Tracks to OFF and a track ident is part of

your route, the Tracks and information outside of your route are

removed. Your route and route points identifying the Track remain on

the map. For more information, see Displaying Organized Track System

Data on page 64.

- In the VFR theme, you can show or hide Low Altitude Airways, and

Other Routes. Other Routes include VFR Routes and Military Training

Routes.

• Waypoints

- Show Waypoints at all Scales: If your company has enabled this option,

you can customize your view to Show Waypoints at all Scales

regardless of the map zoom level.

- Show Only Oceanic Entry/Exit: In IFR themes, you can filter the map to

show only oceanic entries and exit points. In the VFR theme, you can

show or hide low altitude waypoints, VFR checkpoints, and VFR

waypoints.

• Navaids

- Show Navaids at all Scales: If your company has enabled this option,

you can customize your view to Show Navaids at all Scales regardless

of the map zoom level.

• Airspace

You can customize airspace to show or hide:

- Controlled airspace

- ATC sectors

- Restricted, prohibited, warning, and danger areas, and Other. Other

includes ADIZ, alert areas, equipment boundaries, MOAs, QNE/QNH

and training areas

- ETOPS rings, if your company provides this supplemental enroute data

• Terrain - No additional filters are available for terrain.

• Cultural Information - The cultural information button is available from the

VFR theme. You can customize cultural information to show or hide city

names, city patterns, high tension lines, obstacles, railroads, and roads.

Accessing Enroute Information

Filtering Enroute Map Objects

Filtering Airports by Runway Length

Filtering airports by runway length enables you to limit the airports that display on

the enroute map.

 To filter airports by runway length:

1. Tap the expand filters menu button to open the menu.

NOTE: The filters menu opens to the Airports menu by default.

2. Tap the Airports object button to show airports.

3. Tap the Minimum Rwy Length value (blue text) and select the desired runway

length.

Tap away from the expanded menu or tap the expanded filters menu button to

close the menu.

Showing Only Oceanic Entry and Exit Points

Displaying only oceanic entry and exit points can be useful in certain areas of the

world.

 To show only oceanic entry and exit points:

1. From either the High IFR or Low IFR enroute theme, tap the expand filters

menu button to open the menu.

2. Tap the Waypoints button to access the filter.

3. Switch Show Only Oceanic Entry/Exit to ON.

Tap away from the expanded menu or tap the Filters Menu button to close the

menu.

Show at All Scales  Airports, Waypoints, and Navaids

In less dense parts of the world, you might need to view airports, waypoints, and

navaids at a larger map scale so that you can view this data within the context of

your route and other information on the map.

At your company’s discretion, FliteDeck Pro can provide a way to view certain

objects at all scales, regardless of your zoom level.

NOTE: The Show at All Scales option is only available if your EFB administrator

enables the option.

 To view airports, waypoints, and/or navaids at all scales:

1. Tap the expand filters menu button to open the menu.

2. For each of the following objects that you want to view at all scales, tap the

corresponding button:

- Airports

- Waypoints

ccessing Enroute Information

Filtering Enroute Map Objects

- Navaids

3. Switch Show At All Scales to ON.

Displaying Organized Track System Data

FliteDeck Pro can display data for North Atlantic Tracks (NAT), Pacific Organized

Track System (PACOTS), and Australian Organized Track Structure (AUSOTS).

Flex Tracks, which are a part of PACOTS, also display.

FIGURE 24: North Atlantic Track with an active flight displayed

You can:

• Load and view the Oceanic Track Systems, including the Australian and

Pacific.

• Load, view, and also route on the North Atlantic tracks.

To display Organized Track System data, the following conditions must be met:

• Display Organized Track Systems is set to ON in FliteDeck Pro global settings.

• You are viewing the enroute map in either the High IFR or the Low IFR enroute

theme.

• Show Organized Tracks is selected in the Airways filter menu.

NOTE: It is recommended that the first time you switch Display Organized Track

Systems to ON in FliteDeck Pro global settings, you have an established

Internet connection.

Retrieving Organized Track System Data

With an Internet connection and Display Organized Track Systems set to ON in

FliteDeck Pro global settings, FliteDeck Pro attempts to retrieve Organized Track

System data on a 30-minute interval and when any of the following occurs:

• You launch FliteDeck Pro.

• FliteDeck Pro wakes up from sleep mode.

• You switch Show Organized Tracks to ON in the Airways filter menu.

Accessing Enroute Information

Filtering Enroute Map Objects

Viewing Track Details

From either the High or Low enroute theme, you can filter organized track system

data ON and OFF from the Airways filter menu. FliteDeck Pro displays the last

time the Organized Track System data was updated from the Airways filter menu.

Although the show and hide status of Organized Tracks is controlled with the

Airways map object button, Organized Tracks can be viewed on the enroute map

at higher zoom levels than other airways. For more information, see For more

information, see Enroute Map Object - Default Zoom Level Display on page 60.

From the map, FliteDeck Pro displays:

• The track identifier.

• The defining waypoint, which can be a named waypoint or a latitude/longitude

waypoint.

• A color coded track line that indicates directionality.

- West to East set is purple.

- East to West set is orange.

Tapping an organized track from the enroute map displays additional details

about the track, including the flight level assigned to the track.

FliteDeck Pro displays Organized Track System data for the most current track

message data it has received for future effective and current tracks.

FIGURE 25: Showing North Atlantic Track Info - West | F track details

FliteDeck Pro does not display expired tracks, and will not retain expired OTS

data (track message data). FliteDeck Pro does not export the Track Data

Message.

NOTE: Always check track effectivity time with current Zulu time.

When you filter Show Organized Tracks to OFF and a track ident is part of your

route, the Organized Track System tracks and information outside your route are

removed. Your route and route points identifying the track remain on the map.

ccessing Enroute Information

Filtering Enroute Map Objects

Searching for Enroute Map Objects from the Map

FliteDeck Pro searches for airports and fixes (including waypoints and navaids)

across all enroute themes on the enroute map, the Route list, and the text of all

notes and Jeppesen Airway Manuals.

FliteDeck Pro searches for enroute objects whether they are filtered to show or

hide on the enroute map.

About Search Results

FliteDeck Pro search results have the following characteristics:

• They are not limited by the map view. You can pan the map or zoom out to see

search results outside the current map view.

• They appear in the search results list and are ordered by distance either from

the map center or from your aircraft position. You can scroll the list to see the

name and distance of objects that are farther away.

• They are returned across enroute themes (High IFR, Low IFR, and VFR).

• They are not limited to objects filtered on the map.

Searching for Enroute Map Objects

 To search for objects on the enroute map:

1. Tap the Search button while viewing the enroute map.

2. Enter text in the search field.

FliteDeck Pro begins searching after you enter two to three characters and

refines results as you type.

FliteDeck Pro indicates the number of results on the Search Results button

and highlights the objects that meet the search criteria on the map, in the

Route list, and under the Pubs tab.

Accessing Enroute Information

Filtering Enroute Map Objects

- Tap the Search Results button to display the Search Results popover.

FliteDeck Pro displays the Search Results popover with the All tab selected

(by default) - or the last viewed tab.

Tap each tab to refine your search results. Text matching the search query in

each category is highlighted. You might need to tap See All for a category to

view all search results in a specific category.

3. Select a search result to view the details.

ccessing Enroute Information

Displaying Enroute Weather

To receive enroute weather data, ensure that display Enroute Wx is set to ON in

FliteDeck Pro global settings, and you have an established Internet connection.

Viewing Enroute Weather

 To display enroute weather, from the enroute map:

1. Tap the Wx button from the control bar.

2. Switch Weather to ON.

3. Tap the weather type that you want to view.

Enroute weather includes surface observations, RADAR (NEXRAD, echo tops,

lightning), icing, turbulence, and winds aloft forecasts

After you establish an Internet connection and switch Weather to ON from the

control bar, FliteDeck Pro checks the selected weather type for updates and

downloads weather data within the radius of your route or scales the data to your

coverage area.

Refreshing Enroute Weather Data

Weather information for the selected weather type is automatically checked every

six minutes. At this interval, only weather that has been updated on the Jeppesen

Weather server is updated on your iPad.

You can also manually update a selected weather type by tapping the Refresh

button at the bottom of the Weather popover.

Accessing Enroute Information

Displaying Enroute Weathe

Viewing Surface Observations

 To view surface observations:

1. Tap the Wx button from the control bar.

2. Switch Weather to ON.

3. Tap the Surface Observations button.

4. Tap away from the Weather popover to dismiss it.

Viewing Icing, Turbulence, and Winds Aloft Forecasts

 To view icing, turbulence, or winds aloft forecasts:

1. Tap the Wx button from the control bar.

2. Switch Weather to ON.

3. Tap the Icing, Turbulence, or Winds Aloft button.

4. Tap the altitude at which you want to view the forecast weather.

5. Tap away from the Weather popover to dismiss it and view the weather

overlaid on the map.

NOTE: You can display up to four weather forecast images. To change to a

different forecast period after you select the weather type, tap the

Forecast button and then select a different forecast time.

Viewing NEXRAD

 To view NEXRAD:

1. Tap the Wx button from the control bar.

2. Switch Weather to ON.

3. Tap the NEXRAD button.

4. Tap the type of NEXRAD weather (Radar Mosaic, Echo Tops, Lightning) that

you want to view.

5. Tap away from the Weather popover to dismiss it and view the weather

overlaid on the map.

6. Tap the Play button to cycle through the series of images.

NOTE: After you tap Play, the animation continues to cycle through the images

until you either tap the Pause button or de-select the weather type to stop

viewing it.

ccessing Terminal Information

Working with Terminal Chart Information

Accessing Terminal Information

From accessing Chart Change Notices to viewing ownship on terminal charts, FliteDeck Pro enables you to

increase situational awareness by viewing your flight with respect to the terminal air structure.

Working with Terminal Chart Information

You can view Chart Change Notices for the selected airport when you are viewing

terminal charts. FliteDeck Pro also makes it easy to highlight, rotate, and print

selected terminal charts.

Viewing Chart Change Notices

 To view chart change notices:

• Tap the Route list button while viewing terminal charts.

FliteDeck Pro displays a scrollable list of change notices for the selected

airport.

On Demand Change Notices

You can view the most recent change notices by tapping the jeppesen.com link

at the bottom of the Chart Change Notices display.

These Change Notices contain the same content that Chart Change Notices

contain, except that these On Demand Change Notices are updated on a daily

basis and you can search for a single airport or FIR.

NOTE: Always check NOTAMs and other pertinent information prior to flight.

Highlighting a Chart

FliteDeck Pro provides two colors for you to choose from when highlights a chart

or the AMM. Tap the Highlight Color button above the highlight button to switch

between the two colors. The selected color displays in the foreground

 To highlight information on a terminal chart:.

• Tap the Highlight button.

• In highlight mode, your finger acts as a highlighter on the chart.

• Tap the Highlight button again to exit highlight mode or tap one of the

following buttons:

• Undo button to remove the last highlight.

• Clear All button to clear all highlights.

Accessing Terminal Information

Displaying Ownship Position on Terminal Charts

NOTE: Highlights persist on the chart until you remove the highlights, or update

the chart. Highlights are not shared with the flight information when you

share flight information from one iPad to another.

Rotating a Chart

To rotate a chart, tap the Rotate button. Each time that you tap the Rotate button,

the chart turns 90 degrees clockwise.

NOTE: When you share flight information from one iPad to another, the rotated

view is not shared with the flight information.

Printing a Terminal Chart

 To print the displayed chart to an AirPrint-enabled printer:

1. Tap the Settings button on the FliteDeck Pro toolbar.

2. Tap Print.

3. Select the printer and the number of copies.

4. Tap the Print button.

NOTE: Charts print out one per page and cannot be re-formatted.

Displaying Ownship Position on Terminal Charts

For those authorized to display ownship, you can also display ownship on terminal

charts to enhance situational awareness during critical phases of flight.

NOTE: Displaying ownship position on the airport diagram is designed to assist

flight crews in orienting themselves on the airport surface and improving

pilot positional awareness during taxi operations. This function is not to be

used as the basis for ground maneuvering and is limited to ground

operations.

Displaying Ownship on Approach Charts

Ownship position is available on approach charts when:

• Display Ownship on Approach Charts in FliteDeck global settings is set to ON.

• Moving Map in the Airport Moving Map of FliteDeck global settings is set to

ON.

• GPS accuracy is better than 200 meters.

ccessing Terminal Information

Displaying Ownship Position on Terminal Charts

Temporarily Disable Display of Ownship Position Approach Charts

There may be situations when you want to temporarily disable the ownship from

appearing on the approach chart.

To do so, tap the GPS Status button while viewing the approach chart, and switch

Ownship on Approach to OFF.

Viewing the Off-Map Indicator on Approach Charts

FliteDeck displays an off-map indicator on the approach chart as a visual cue to

indicate the direction from which your aircraft is approaching when these

conditions are met:

• Display Ownship on Approach Charts in FliteDeck Pro global settings is set to

ON.

• Your aircraft is within 10NM of the approach chart boundary.

• The minimum GPS accuracy requirements to display ownship position on

approach charts are met.

Displaying Ownship on SID and STAR Charts

FliteDeck Pro displays ownship position on SID and STAR geo-referenced, or to-

scale, charts when these conditions are met:

• Display Ownship on SID/STAR Charts in FliteDeck Pro global settings is set to

ON.

• GPS accuracy is better than 200 meters.

Displaying Ownship on Taxi Charts

FliteDeck Pro displays ownship position on taxi charts when these conditions are

met:

• Display Ownship on Taxi Charts in FliteDeck Pro global settings is set to ON.

• Your aircraft is moving no faster than the speed specified in the Arpt Diagram

(10-9) Speed Threshold in FliteDeck Pro global settings. The speed threshold

is 40 knots by default.

• GPS accuracy is better than 25 meters.

Accessing Terminal Information

Displaying Terminal Weathe

Automatically Displaying the Taxi Chart Upon Landing

FliteDeck Pro automatically switches to the airport diagram upon landing when

these conditions are met:

• Show Taxi On Landing is set to ON from the Settings button on the FliteDeck

Pro toolbar.

• Your aircraft is moving no faster than the speed specified in the Arpt Diagram

(10-9) Speed Threshold in FliteDeck Pro global settings. The speed threshold

is 40 knots by default.

FliteDeck Pro will switch to t the AMM upon landing (instead of the taxi chart)

under the same conditions if your company subscribes to AMM and you switch

Set as Default on Landing to ON from the AMM setting in FliteDeck Pro global

settings.

Displaying Terminal Weather

You can display METAR and TAF information while viewing a terminal chart or

Airport Moving Map (AMM), and from airport details in the Route list.

To receive terminal weather information, ensure that Display METAR/TAF is set

to ON in FliteDeck Pro global settings and that an Internet connection is estab-

lished.

NOTE: Weather data is provided by Jeppesen. Source data is provided primarily

by the National Weather Service and the UK Met Office as well as other

private weather providers that Jeppesen utilizes in creating aviation-

specific weather information.

Displaying METAR/TAF

To display METAR and TAF information do one of the following:

• Tap the Wx button from the control bar while viewing a terminal chart or the

Airport Moving Map.

• Tap the Wx flyout from airport details in the Route list.

Updating METAR/TAF Information

If the weather data is expired, a weather warning appears in red in the same

location as the weather age.

To manually update METAR/TAF information, tap the Refresh button at the

bottom of the Weather popover.

ccessing Terminal Information

Working with Mid-Cycle Chart Updates

Whenever terminal charts are updated, most of the charts are effective upon

receipt and available to you immediately in FliteDeck Pro.

A mid-cycle chart revision occurs when a chart takes effect in the middle of a

scheduled chart revision time period.

For charts that take effect mid-cycle, FliteDeck Pro displays an amber effectivity

badge which indicates that a mid-cycle chart revision is available at that airport.

The badge appears 24 hours before and after the chart effectivity change.

NOTE: Always brief selected terminal charts, including a review of effectivity

dates, as part of your briefing.

Switching Between Available Chart Versions from the

Airports List

Whenever revisions exist for a chart at an airport in your route, FliteDeck Pro

displays an effectivity badge on the Airport button and in the Route Airports list.

 To view effective dates and access the option to switch between

available chart versions from the Route Airports list:

1. Tap the Airport button.

FliteDeck Pro displays the list of Route Airports for the active flight, and airport

effectivity text and badges, if applicable.

2. Tap the Airport Effectivity badge next to the airport with the chart revisions.

FliteDeck Pro displays the Airport Revision Selector and prompts you to

choose the effectivity date of the charts that you want to view.

3. Complete the action by doing one of the following:

• Tap Cancel to dismiss the Airport Revision Selector and continue viewing the

current chart version.

• Tap the date to use a chart with a different effectivity date, and then tap Done.

Switching Between Two Available Charts While Viewing the Chart

When you view a chart with more than one version available, FliteDeck Pro

displays chart revision text in the chart list and a chart revision tag on the chart

itself.

Accessing Terminal Information

Working with the Airport Moving Map (AMM)

 To view effective dates and access the option to switch between

available chart versions while viewing a chart:

1. Tap the Chart Revision tag.

FliteDeck Pro expands the Chart Revision tag and indicates the effective date

of the chart being used.

2. To switch between available chart versions, tap the Switch button.

FliteDeck Pro displays the Airport Revision Selector and prompts you to

choose the effectivity date of the chart that you want to view.

Working with the Airport Moving Map (AMM)

When your company subscribes to Airport Moving Map (AMM) and AMM is

available at the selected airport, FliteDeck Pro displays Chart/AMM buttons at the

bottom of the taxi chart display.

AMM displays depictions of gates, center lines, hot spots, and other enhanced

details that further enhances your situational awareness on the ground.

NOTE: Airport Moving Map is not available for all airports and each operator can

subscribe to as many or few airports as required for their operation.

About Airport Moving Map

F FliteDeck Pro switches to Airport Moving Map when you tap the AMM button at

the bottom of the taxi chart display. To return to the taxi chart, tap the Chart

button.

If you navigate away from AMM and then return, the map orientation, zoom level,

and pan locations displays in the same state as when you left.

You highlight AMM in the same way you highlight your terminal charts.

NOTE: Airport Moving Map is a supplement to the airport diagram and not to be

used as a replacement for the taxi chart.

ccessing Terminal Information

Working with the Airport Moving Map (AMM)

Displaying Ownship on AMM

For those operators authorized to display ownship and moving map in flight, the

ownship position is available on the Airport Moving Map when:

• Display Ownship under the Airport Moving Map setting in FliteDeck Pro global

settings is set to ON.

• Moving Map under the Airport Moving Map setting in FliteDeck Pro global

settings is set to ON.

• Your aircraft speed is less than the setting in Taxi on Landing Speed

Threshold in FliteDeck Pro global settings.

• GPS accuracy is better than 45 meters.

• Ownship is within the airport boundary.

Viewing Moving Map

You can view Moving Map on the AMM depiction without displaying ownship

when:

• Moving Map (and not Display Ownship) is set to ON under the Airport Moving

Map setting in FliteDeck Pro global settings.

• GPS accuracy is better than 45 meters.

• Ownship position is within the airport boundary.

In this case, the map moves along with ownship position, and the Present Position

and Map Orientation buttons are still available - just without the display of

ownship.

Viewing Present Position

To recenter the Airport Moving Map over ownship position after you have panned

away, and GPS requirements are being met, tap the Present Position button

from the map.

When you pan away from the airport depiction while GPS requirements are not

being met, tapping the Present Position button will reposition the airport map so

that the airport reference point is at the center of your view.

NOTE: When Moving Map is enabled, any action that pans the map stops it from

moving. Tapping the Present Position button on the enroute map resumes

the moving map.

Accessing Terminal Information

Working with the Airport Moving Map (AMM)

Switching Map Orientation

To change the Airport Moving Map orientation, tap the North Up or Track Up

button on the enroute map to switch between orientations.

The Track Up button is available on the Airport Moving Map when:

• Moving Map in the Airport Moving Map of FliteDeck global settings is set to

ON.

• Aircraft speed is less than set in Taxi on Landing Speed Threshold in FliteDeck

global settings.

• GPS accuracy is better than 35 meters.

• Ownship is within the airport boundary.

Highlighting the Map

Highlights persist on the chart until you remove the highlights, or update the AMM

depiction.

 To highlight information on the Airport Moving Map:

• Tap the Highlight button.

In highlight mode, your finger acts as a highlighter on the map.

• Tap the Highlight button again to exit highlight mode or tap one of the

following buttons:

• Clear All button to clear all highlights.

• Undo button to remove the last highlight.

NOTE: Highlights are not shared with the flight information when you share flight

information from one iPad to another.

Automatically Displaying the Airport Moving Map on

Landing

FliteDeck automatically switches to the Airport Moving Map upon landing when

these conditions are met:

• You switch Set as Default on Landing to ON from the Airport Moving Map

(AMM) setting in FliteDeck global settings.

• Your aircraft is moving no faster than the speed specified in the Taxi on

Landing Speed Threshold field in FliteDeck global settings.

Managing Data Updates

Performing Data Updates

Managing Data Updates

FliteDeck Pro provides a simple way to verify the status of your enroute, terminal chart, and manuals text data.

At any time, you can tap the Settings button from the FliteDeck Pro toolbar, and then tap Updates to view the

status of your data. All dates are in ZULU time format.

Performing Data Updates

Whenever data updates are available, a badge appears on the Settings button.

The badge indicates the number of updates available.

• The badge is amber when data is current, and an update is available.

• The badge is red when data is not current, and an update is available.

NOTE: The time necessary to download and perform updates depends on the

speed of the Internet connection and the size of the data coverage area.

Ensure that you have the necessary time and bandwidth to perform the

complete update before commencing the update.

Performing Data Updates

 To perform a data update:

1. Tap the Settings button.

2. Tap Updates.

3. Tap the Update button.

4. When updates are complete, tap the X at the top of the Updates screen to

dismiss it.

• At any time during an update, you can pause the download by tapping the

Pause button on the status line. If more than one update is available, FliteDeck

Pro automatically begins to download the next available update.

• To resume downloading after pausing an update, tap the Resume button at

the top of the update status line.

• To cancel all updates and exit Updates, tap the X at the top of the Updates

screen. To resume updates after having canceled, tap the Settings button, tap

Updates, and then tap the Resume button.

Managing Data Updates

Performing Data Updates

About Data Status Color Codes

The following list describes the meaning of the colors in the Updates bar:

• Green: Current data is in use.

• Amber: Current data is in use and an update is available.

• Red: Data is not current, and an update is available.

When two sets of data are available, the bar color codes are:

• Light Green: Current data is in use.

• Dark Green: Data is available but not in use.

• Light Red: Data is not current.

• Dark Red: Next update has not been downloaded.

Switching Between Two Available Enroute Databases

FliteDeck Pro updates the enroute database every 28 days. The app automati-

cally switches to the current database when it takes effect (if you downloaded the

database).

You can download enroute data up to seven days before the effective date.

Because of this rule, two versions of the enroute database can exist on your

device at the same time.

FliteDeck Pro displays an amber flag on the map 24 hours before a database

expires, to indicate that the current database expires soon.

Also, if you select a database that either is expired or is not yet effective,

FliteDeck Pro displays a similar amber flag that indicates the status of the data.

That is, the app shows a flag whether the data is expired or is not yet effective.

To manually change enroute database versions when more than one version is

available:

1. Tap the Settings button.

2. Tap Updates.

3. Tap the Switch Back to Data Expiring [date] to view that database.

4. To return to the current database, tap Switch to Data Effective [date].

Managing Data Updates

bout Unscheduled Updates

About Unscheduled Updates

FliteDeck Pro enables you to complete an unscheduled update at any time.

An unscheduled (or off-cycle) update is an unplanned change. For example, an

unscheduled update can occur due to an error on an existing chart or, in the case

of company manuals, when a publication is not part of an update cycle.

Unscheduled updates are initiated by your company or by Jeppesen on a case-

by-case basis.

Whenever any data updates are available (scheduled or unscheduled), a badge

appears on the Settings button on the FliteDeck Pro toolbar. The badge indicates

the number of updates available.

Performing an Unscheduled Update

 To perform an unscheduled update:

1. Tap the Settings button from the FliteDeck Pro toolbar.

2. Tap Updates.

3. FliteDeck Pro displays an alert if an unscheduled update is available.

4. Tap the Update button.

5. When updates are complete, you can tap the X at the top of the Updates

screen to dismiss it.

Managing Data Updates

Understanding Messages and Error Codes

FliteDeck Pro displays warning messages and error codes to convey information

when it encounters specific conditions related to the status of your data.

Although this information is presented for your general knowledge and you should

contact your company system administrator or Jeppesen technical support, you

can now also search for an error code or message to learn more about it using the

in-app Help.

 To access the in-app Help:

1. From the Settings button, tap Help.

2. Tap in the Search field and enter the error code you are searching for.

FliteDeck Pro performs a predictive search as you type.

3. Tap the resulting Understanding Messages and Error Codes topic flyout.

FliteDeck Pro highlights the search term in the topic.

FIGURE 26: Error code search result from the in-app help

4. Tap Search Results to return to the search results, or Done at the top of the

popover to dismiss the Help screen.

Managing Data Updates

Understanding Messages and Error Codes

For your reference, this information related to error codes and warming messages

is included here, as well.

Error Reason Resolution

-1 FliteDeck Pro generated a general data

download error, most likely due to slow

Internet connection.

Check for a reliable Internet connection

and ensure that the speed is at least 54

mbps. Then, to attempt the download

again, tap Refresh on the Update

screen.

101 The device has already been success-

fully registered. The Recipient state

shows as “Active,” “In Configuration,” or

“Out of Configuration” in JDM Pro.

If the device must be activated with a

different recipient, deactivate FliteDeck

Pro, and then reactivate it.

(If the device is already activated with

the correct recipient, verify whether the

user can retrieve any assigned data. If

not, contact Jeppesen Support.)

102 The URL used by FliteDeck Pro for

registration is not valid. The registration

email is garbled or incomplete.

Generate another registration email and

contact Jeppesen Support.

103 One of the following issues might cause this error:

1 The connection to JDM Pro server is

faulty due to a connectivity issue on

the user side.

Try again later from a better connection.

2 The connection to JDM Pro server is

faulty due to a connectivity issue on

the server side.

Try again later.

3 The registration message sent to the

CDL is garbled or incomplete.

Try again later.

4 The registration email is expired (that

is, more than three days old).

Generate another registration email.

5 The user tried to register a device that

is already registered.

Try to deactivate the app.

105 File processing failed due to a mismatch

of the stored and calculated digest

values. Processing cannot continue.

The user must request the file again.

Any temporary files are automatically

removed from the device.

106 This error indicates a generic unzip

process failure. Processing cannot

continue.

The user must request the file again.

Any temporary files are automatically

removed from the device.

107 This error indicates a generic deltaset

processing failure. The deltaset

processing cannot continue.

FliteDeck Pro automatically attempts to

download the full version for this data.

Any temporary files are automatically

removed from the device.

109 This error might indicate a number of

issues, ranging from network or server

issues to a lack of available disk space.

First ensure that the device has

adequate space and that a reliable

network connection is available. Then try

again later.

Managing Data Updates

Understanding Messages and Error Codes

110 The download URL that JDM Pro sends to FliteDeck Pro does not point to a file.

One of the following issues might cause this error:

1 Content is not available yet. A delay

of less than 5 minutes is normal

between the time that the content is

uploaded and the time that it is

available.

Try again later.

2 The connection to the JDM Pro server

is faulty due to a connectivity issue on

the user side.

Try again later from a better connection.

3 The connection to the JDM Pro server

is faulty due to a connectivity issue on

the server side.

Try again later.

4 JDM Pro received the data, but the

data has not yet reached the remote

servers. This process can take from a

few minutes to up to an hour.

Try again later.

5 The content assigned in JDM Pro is

expired or is no longer in effect. You

cannot download an expired file from

the remote servers, even if content is

assigned in JDM Pro.

Assign a non-expired version of the

content and try again.

112 FliteDeck Pro did not receive the expected configuration from JDM Pro. This error

might indicate “server not found” or “timed out connecting to server.” One of the

following issues might cause this error:

1 The connection to the JDM Pro server

is faulty due to a connectivity issue on

the user side.

Try again later or from a better

connection.

2 The connection to the JDM Pro server

is faulty due to a connectivity issue on

the server side.

Try again later.

3 FliteDeck Pro received an expected

configuration that is invalid or null.

Verify the recipient settings in JDM

Pro.

If the recipient settings are correct, try

the request again.

4 FliteDeck Pro made multiple

successive requests over a slow

network connection.

Advise the user to wait a few seconds

between making requests when using a

slower or unreliable network.

5 A recipient was deleted from JDM

Pro, and then recreated using the

same name, without deactivating or

re-registering the device. This action

causes CDL to contact the server

using a valid user name but old regis-

tration credentials. In this case, JDM

Pro returns an empty response, which

CDL interprets as a 112 error.

First, deactivate FliteDeck Pro. Then

generate a new activation link and use it

to reactivate the app.

Error Reason Resolution

Managing Data Updates

Understanding Messages and Error Codes

120 This error indicates a deltaset

processing failure.

FliteDeck Pro automatically attempts to

download the full version for this data.

Any temporary files are automatically

removed from the device.

121 Disk space is exhausted. Clear disk space on the device and try

again.

124 The user attempted to register. The CDL has a network connection but cannot

connect to the registration server. One of the following issues might cause this

error:

1 The network connection failed due to

a connectivity issue on the user side.

Try again later, or try from a better

connection.

2 The network connection failed due to

a connectivity issue on the server

side.

Try again later.

3 The JDM Pro server is unavailable.

Try again later.

125 The user attempted to register but CDL timed out trying to connect to the registra-

tion server. One of the following issues might cause this error:

1 The device is not connected to the

Internet.

Obtain a local connection and try again

2 The network connection is faulty due

to a connectivity issue on the user

side.

Try again later or from a better

connection.

3 The network connection is faulty due

to a connectivity issue on the server

side.

Try again later.

4 The JDM Pro server is unavailable.

Try again later.

126

FliteDeck Pro tried to contact JDM Pro.

CDL has a network connection but could

not connect to the JDM Pro server.

The network connection is faulty due to

a connectivity issue on the user side.

Try again later.

The network connection is faulty due to

a connectivity issue on the server side.

Try again later.

The JDM Pro server is unavailable.

Try again later.

Error Reason Resolution

Managing Data Updates

Understanding Messages and Error Codes

127 The user attempted to contact JDM Pro but CDL timed out trying to connect. One of

the following issues might cause this error:

1 The device is not connected to the

Internet.

Obtain a local connection and try again.

2 The network connection is faulty due

to a to connectivity issue on the user

side.

Try again later or from a better

connection.

3 The network connection is faulty due

to a connectivity issue on the server

side.

Try again later.

4 The JDM Pro server is unavailable.

Try again later.

129 FliteDeck Pro was unable to obtain a

network connection.

Ensure that wireless connectivity is

turned on in the device settings and that

a reliable network connection is

available.

133 Enroute, cultural, or terrain data required

by the application is not assigned to the

distribution group the recipient belongs

to in JDM Pro.

Ensure that new data formats are in the

appropriate JDM Pro group.

136 The JDM Pro certificate stored locally on

the device expired or is about to expire.

An attempt was made to renew the

certificate, but the attempt failed. The

application continues to acquire data

until the certificate expires.

NOTE: Regardless of the error,

FliteDeck Pro continues to

acquire content successfully

until two-way SSL is enabled on

the Jeppesen servers.

Contact the JDM Pro administrator.

180-186,

188-189

These errors indicate deltaset

processing issues.

The software automatically discards the

deltaset in favor of the larger, full

dataset.

187 This error indicates a disk space issue. Free up disk space on the device, and

then try again.

199 Terminal charts content is not assigned

to the recipient in JDM Pro, or FliteDeck

Pro expects new content to be available

on the server, but the content is not

available yet.

Contact the JDM Pro administrator.

The correct content items must be

present for the distribution group and

correctly added to the recipient

registered to the device.

201

Product entitlement invalid. The AVP

signature or Airport Moving Map (AMM)

data is invalid.

Contact technical support.

Error Reason Resolution

Managing Data Updates

Understanding Messages and Error Codes

211

Supplemental Enroute data (Tailored

Enroute) and Airport Moving Map (AMM)

data could not be loaded. Enroute data

downloaded but neither Tailored

Enroute

data nor AMM data has been

downloaded

for the currently selected cycle.

Contact technical support.

212

Supplemental Enroute data (Tailored

Enroute) could not be loaded. Enroute

data has been downloaded but Tailored

Enroute data has not been downloaded

for

the currently selected cycle.

Contact technical support.

221

Invalid Airport Moving Map (AMM) data.

Loaded AMM data for the currently

selected cycle cannot be displayed.

Contact technical support.

222

Supplemental Airport Moving Map

(AMM)

data could not be loaded. Enroute data

has been downloaded but AMM data

was

not downloaded for the currently

selected

cycle.

Contact technical support.

400–600 Error codes in this number series

indicate issues that originate in JDM

Pro.

Contact the JDM Pro administrator and

determine whether the JDM service that

you are currently using is experiencing

technical issues.

1009 FliteDeck Pro attempted to download

data, but there no Internet connection is

established.

Obtain a local Internet connection and

try again.

3006 FliteDeck Pro is unable to write to a file.

Insufficient disk space or a permissions

issue might cause this condition.

Free up disk space, and then try to

download the data again.

3008 FliteDeck Pro was unable to download

data, most likely due to a network issue.

Try the download again, or wait for a

better connection and try the download

later.

3026 A request failed. Retry the operation with a better Internet

connection, or at later.

Error Reason Resolution

Managing Data Updates

Understanding Messages and Error Codes