XIL-7RDKIT-v2_instructions.indd

VISIONXLIGHTING.COM

Installation Instructions & User’s Manual

VISION X

About The VX SERIES 7” HEADLIGHT

FEATURES

1. LED Halo

2. DOT approved

3. Multiple wiring connections available

VX SERIES 7” HEADLIGHT SPECIFICATIONS

1. Warranty : Extended

2. Amp Draw : High 3.0A/ Low 2.2A/ Halo 0.33A @12V

3. Input Voltage : 9-32V

4. Beam Patterns : High, Low, Halo

5. LED Lifespan : 50,000 Hours

PREPARATION

1. We recommend completely reading instructions before

installing.

2. Consult your local state regulatory agency regarding the

use of LED lighting.

3. The placement of LED lighting should not restrict airow to

the radiator, or block head lamps, turn signals, or parking

lights.

MAINTENANCE

1. All Vision X models have been designed for

maintenance free use. In the case an LED lamp or other

part replacement is needed please contact your authorized

service center.

VX SERIES LED HEADLIGHT

Qty: 2

7” Headlight

XIL-7RD

WARNINGS

As with many other high-tech products, this VISION X LED

requires a bit of attention before you can use it. Please read

the accompanying information carefully rst.

1. Don’t stare directly into the light or shine directly into the

eyes of another person as this may cause temporary loss

of vision.

2. Never disassemble the products, as all parts must be

factory serviced to insure proper operation.

3. Don’t interchange the parts inside this light with other

products.

4. The LED light is to be mounted on the vehicle only in a

vertical, bottom mounting, or in a suspended position.

5. After turning on the light, the body might be hot enough

to warrant a burn risk. Be careful when you touch the

body after turning on the light for a long period of time.

6. Use the supplied wire harness for electrical installation.

7. The LED light must not adversely aect the performance

of low beam, high beam, engine cooling or the driver’s

view.

Qty: 2

7” Headlight

XIL-7RD

Qty: 2

H4 Plug

P-HLH42H13

XIL-7RDKITJK

XIL-7RDKIT

VISION X

Gore-Tex

Cap (ON)

REMOVE

Gore-Tex

Cap (OFF)

Having a correct venting solution in place can impact

the lamps longevity and durability. The Gore-Tex valve

equalizes pressure bi-directionally and manages moisture all

while providing spray, immersion, and splash protection in the

event the valve is exposed to the elements.

GORE-TEX VALVE

Figure 1

VX SERIES LED HEADLIGHT

SEE VEHICLE OWNERS MANUAL FOR HELP REPLACING HEADLIGHT

ADDITIONAL WIRING HARNESS ADAPTER MAY BE NEEDED CONSULT

YOUR DEALER TO DETERMINE IF ONE IS NEEDED

1. Disconnect vehicle battery prior to installation.

2. Review your vehicle manual for detailed instructions for

removing existing factory head light housing.

3. Remove Gore-Tex Valve Cover, prior to installation see

[Figure 1]

4. Attach VX Series LED Headlight to Optional HI-4 Module

(P–HLHI4), then to the existing factory plug and re-install

according to your vehicles manual. See [Figure 2]

5. To wire the LED Halo Daytime Running light, locate the

white wire on the back of the light. Power the white wire by

attaching it to the accessory power of the vehicle. If there

isn’t accessory power available ax it to the blue wire of

the light or its own aux switch.

WIRING INSTRUCTIONS XIL-7RDKIT

WIRING DIAGRAM

Red = High Beam [ + ]

Blue = Low Beam [ + ]

Black = Ground [ - ]

White = Halo [ + ]

WIRING KEY

white

black

blue

red

Plug

OPTIONAL

P-HLHI4

Figure 2

VISION X

WIRING DIAGRAM

Red = High Beam [ + ]

Blue = Low Beam [ + ]

Black = Ground [ - ]

White = Halo [ + ]

WIRING KEY

1. Disconnect vehicle battery prior to installation

2. Review your vehicle manual for detailed instructions for

removing existing factory head light housing.

3. Remove Gore-Tex Valve Cover, prior to installation see

[Figure 1]

4. Attach VX Series LED Headlight to Optional JEEP JK HI-4

Module (P–HLHI4H13), then to the existing factory plug and

re-install according to your vehicles manual. See [Figure 3]

5. To wire the LED Halo Daytime Running light, locate the

white wire on the back of the light. Power the white wire by

attaching it to the accessory power of the vehicle. If there

isn’t accessory power available ax it to the blue wire of the

light or its own Aux switch.

white

black

blue

red

H13

Plug

OPTIONAL

P-HLHI4H13

WIRING INSTRUCTIONS XIL-7RDKITJK

SEE VEHICLE OWNERS MANUAL FOR HELP REPLACING HEADLIGHT

ADDITIONAL WIRING HARNESS ADAPTER MAY BE NEEDED CONSULT

YOUR DEALER TO DETERMINE IF ONE IS NEEDED

Figure 3

VX SERIES LED HEADLIGHT

TIP: For complete application guide see web site

STEP 1: Low Beam

STEP 2: Center line of Low Beam

STEP 3: High Beam

TESTING THE LIGHT

1. After all connections have been made start your vehicle

and test your switch to make sure it turns on the light prior

to reassembly.

2. Make sure the angle of your light is correct, otherwise

adjust the light angle again.

3. Make sure no wire or other components of the harness are

exposed to water spray, excessive heat, or moving parts.

P-HLHI4- High Low High 4 adapter engages all three beam

modes simultaneously to dramatically increase visibility and

output.

P-HLHI4H13- High Low High 4 adapter engages all three

beam modes simultaneously to dramatically increase visibility

and output. (For use with XIL-7RDKITJK With H13 Plug)

P-HLCBAH13- Single Canbus Integration adapter levels

electrical current to remove electrical interference from the

vehicle and eliminate ickering in light.(For use with non

XIL-7RDKITJK part #’s)

Halo LowHigh HLHI4

HEAD LIGHT ALIGNMENT

ADAPTERS/ACCESSORIES

VISIONXLIGHTING.COM